Net engine power is with standard equipment including air cleaner,
exhaust system, alternator,and cooling fan
at test conditions
specified per ISO9249.
No derating is required up to 10,000-ft.
(3050 m) altitude.
Specifications and design subject to change without notice.Wherever applicable, specifications are in accordance with SAE standards.
Except where otherwise noted, these specifications are based on units with standard equipment,modular ROPS/cabs, full fuel tanks,
and 175-lb. (79 kg) operators.
DKA91050WH Litho in U.S.A. (07-04)
Base Landfill
Machine Package Engine
●●
Certified to EPA Tier 3 emissions
●●Spin-on vertical oil filter with anti-drainback valve
●●Fuel system includes precleaner with water separator
▲ ● Alternator air prescreener
●●Oil-to-water engine oil cooler
▲ ● Thermal shield for turbocharger and exhaust manifold
●●Electronic engine throttle control
●●Key start switch with electric shutoff
●●Intake-mounted air-inlet heater
Cooling
▲ ● Hydraulically driven fans for engine and hydraulic cooling
systems with automatic reverser on timer and manual switch
●●Radiator and charge air cooler rated 5 fins per in.
●●Radiator and charge air cooler side-by-side design
●●Transmission cooler with hydraulically driven cooling fan
●●Transmission cooler rated 5 fins per in.
● Perforated and corrugated side-shield opening
Powertrain
●●Infinitely variable speed to match ground speed to load
●●Integral final-drive seal protection with in-cab warning before
failure
▲
●
Bolt-on final-drive seal guards
●●Diagnostic test ports
Hydraulics
●●
Two-function hydraulics
●●10/5-micron dual-stage filter element
●●Hydraulic/transmission oil reservoir with service shutoff
●●O-ring seal connectors
●●Diagnostic test ports
Electrical
●●Positive-terminal battery covers
●●Master disconnect
●●Electrically activated battery
● Pre-wired for beacon
Undercarriage
●●Oscillating track frames
▲▲Segmented sprockets
●●Heavy-duty sealed and lubricated track chain
Base Landfill
Machine Package Undercarriage
(continued)
●●Half-shell push-beam bearings
●●Integrated track-frame cover
Operator’s Station
●●Modular-design ROPS/FOPS isolation-mounted cab with left
and right access
●●Heater (35,000 Btu) and air conditioning (28,000 Btu)
●●Pressurized and filtered ventilation with 3-speed blower
●●Left and rear sliding windows
●●Dome light
●●Rubber floor mats
●●Slip-resistant steps
●●Air-suspension fabric seat
●●Adjustable armrests, backrest, height, weight, and fore-aft
●●2-in. (50 mm) seat belt with retractor
●●Radio ready
●●12-volt/10-amp power port
●●Cup holder
●●Interior-mounted rearview mirror
▲ ● Hydraulic oil temperature gauge
Landfill Guarding
▲ ● Bottom tank guards
● Protection bars on side covers
● Protection bars for engine side doors
● Belly pan sealing
● Seal between cab and mainframe
▲ ● Trunnion guard for tilt-cylinder hoses
▲ Striker bars
▲ Blade trash rack
Overall Vehicle
●●
One-piece unitized mainframe
●●On-board cab-tilt system
●●Rear retrieval hitch
●●Rear attachment mounting points integral to mainframe
●●Sight gauges for hydraulic, transmission, and final-drive
seal fluids
▲▲Counterweight with storage compartment
▲▲Hydraulic blade pitch available
▲▲JDLink
TM
950J / 1050J WASTE HANDLERS
Key: ● Standard equipment ▲ Optional equipment *See your John Deere dealer for further information.
CONTROL OWNING AND OPERATING COSTS
Customer Personal Service (CPS) is part of John Deere’s proactive, fix-before-fail strat-
egy on machine maintenance that will help control costs, increase profits, and reduce
stress. Included in this comprehensive lineup of ongoing programs and services are:
Fluid analysis program
– tells you what’s going on inside
all
of your machine’s
major components so you’ll know if there’s a problem
before
you see a decline in per-
formance. Fluid analysis is included in most extended coverage and preventive-main-
tenance agreements.
Component life-cycle data
– gives you vital information on the projected life span
of components and lets you make informed decisions on machine maintenance by telling
you approximately how many hours of use you can expect from an engine, transmission,
or hydraulic pump. This information can be used to preempt catastrophic downtime by
servicing major components at about 80 percent of their life cycle.
Preventive Maintenance (PM) agreements
– give you a fixed cost for maintain-
ing a machine for a given period of time. They also help you avoid downtime by ensur-
ing that critical maintenance work gets done right and on schedule. On-site preventive
maintenance service performed where and when you need it helps protect you from
the expense of catastrophic failures and lets you avoid waste-disposal hassles.
Extended coverage
– gives you a fixed cost for machine repairs for a given period
of time so you can effectively manage costs. Whether you work in a severe-service
setting or just want to spread the risk of doing business, this is a great way to custom-
fit coverage for your operation. And an extended coverage contract also travels well
because it’s backed by John Deere and is honored by
all
Deere construction dealers.
Customer Support Advisors (CSAs)
– Deere believes the CSA program lends a
personal
quality to Customer Personal Service (CPS). Certified CSAs have the knowledge
and skills for helping make important decisions on machine maintenance and repair.
Their mission is to help you implement a plan that’s right for
your
business and take
the burden of machine maintenance off your shoulders.
Vertis QCA
1300 19th Street, Suite 200
East Moline, IL 61244
Cyan
Magenta
Yellow Black
DKA91050WH Page 20
DKA91050WH_SPECS 4/11/07 10:13 AM Page 20
