Filter
Top Products
Owner's Manual
TX158, TX159 ATV Trailers
TX191 Tracking Beam Kit
Check for parts online at www.yutrax.com or call 800-345-6007 M-F 8-5 CST Page 3
FOR TX159
5. Support the trailer far enough off the ground for the assem-
bly of the tracking beams, braces and wheels. Slide the track-
ing beam and brace onto the threaded axle spindle. Secure
in place following this order: tracking beam, tracking beam
brace, 3/4” crown nut and cotter pin. Back crown nut off just
enough so tracking beam will pivot freely and crown nut slot
aligns with hole in threaded axle spindle. Insert cotter pin. Us-
ing a needle nose pliers, bend cotter pin ears around so it will
not come off the axle spindle. Repeat this step for remaining
tracking beam. SEE FIGURES 2 AND 3.
6. Slide the wheel onto the threaded axle spindle of tracking
beams with grease fitting facing outward. Secure in place fol-
lowing this order: wheel, 3/4” washer, 3/4” crown nut and cotter
pin. Back crown nut off just enough so wheel spins freely and
crown nut slot aligns with hole in threaded axle spindle. Insert
cotter pin. Using a needle nose pliers, bend cotter pin ears
around so it will not come off the axle spindle. Repeat this step
for remaining three wheels. SEE FIGURES 2 AND 3.
IMPORTANT NOTE: You must grease the bearings of each
wheel. Using a grease gun, pump high-quality grease into
the bearings by attaching to grease fitting located on wheel
hub. Check the grease level frequently to prevent bearings
from seizing.
FOR BOTH MODELS
7 Attach front trailer frame and the rear trailer frame together
using (2) provided 1/4-20 x 2” bolts, (2) 1/4-20 x 2-1/2” bolts,
(4) nyloc nuts and (8) 1/4” washers. SEE FIGURE 1 OR 2.
8. Attach the front trailer frame (300713) to the axle plates using (2)
provided 1/4-20 x 1-1/2” bolts, (2) 1/4-20 x 2” bolts, (4) nyloc nuts
and (4) 1/4” washers. SEE FIGURE 1 OR 2. Latch the front trailer
frame to the latch located on trailer tongue to hold in place.
9. Attach the rear trailer frame (300710) to the axle plates using
(2) provided 1/4-20 x 1-1/2” bolts, (2) 1/4-20 x 2” bolts, (4) ny-
loc nuts and (4) 1/4” washers. SEE FIGURE 1 OR 2. You must
now tighten all nut & bolt assemblies. Be sure not to over
tighten or crush tubing when tightening!
10. Slide the removable tailgate (300704) into the slots of rear
trailer frame. Slide the removable side rails (300700 & 300701)
into the top side of front and rear trailer frames. SEE FIGURE 1
OR 2.
NOTE: The side rail that goes in the front of trailer frame
is narrower than the others. Lubrication, such as powder
graphite or silicone spray, is recommended at slide-togeth-
er points.
USE INSTRUCTIONS:
1. To use the tilt/pivot feature, simply unlatch the latch located
on trailer tongue. This will allow you to tilt the trailer frame
upward to unload. If pivoting is desired, simply unlatch the
latch and turn the trailer frame to the desired location, left
or right, and tilt trailer frame upward to unload. This feature
works well when in tight areas. Or if backing up your trailer
is not an option, simply drive along side desired unloading
area, unlatch the trailer frame and turn trailer frame to de-
sired location.
Always…
damage or loose/missing bolts & hardware.
from seizing.
Never…
or prescription drugs.
OPTIONAL ACCESSORIES