Filter
Top Products
POP
™
Mode Alerts
Because POP
™
Mode radar utilizes the same
K or Ka band frequencies, POP
™
Mode Alerts will be
displayed as regular radar alerts.
LASER/RADAR ALERTS
Speed Radar Audio/Visual Alerts
When X, K or Ka is detected, the band ID and
signal strength are displayed. The audio alert is
continuous and has a geiger counter-like
pattern. The faster the beep, the closer or
stronger the radar source.
Laser Audio/Visual Alerts
When a laser signal is detected the audio alert is
continuousfor a minimum of 3 seconds.
• The Displays Shows:
Pulse Protection
®
Pulse (or instant-on) radar is more difficult to
detect than conventional radar because it
remains ‘off’ until activated to measure the speed
of a targeted vehicle.
When a pulse type transmission is detected, your
Whistler detector sounds an urgent 3-second
audio warning and the display shows:
After the 3-second pulse alert, the standard alert
pattern continues for as long as the signal is
present.
It is important to respond promptly to a pulse
alert, since warning time may be minimal.
OPERATION
Alert Priority
When two or more signals are received at the
same time, the alert priority is:
1. Laser 2. Speed Radar 3. Safety Radar
Example: If X band is alerting, then suddenly a
laser signal is detected, the laser warning will
override the X band alert.
Compass Calibration Set-up
The unit will need to be calibrated in order for
the compass to provide accurate readings. To
calibrate the unit, perform the following proce-
dure:
1
1
.
.
Mount the unit level in the center of the
vehicle’s windshield. Make sure there are no
other magnetic sources near the detector
(i.e., speaker).
2
2
. Select a large clear area (parking lot or field)
without any power lines.
3
3
. Press the Menu button until display shows
C
C
A
A
L
L
M
M
O
O
D
D
E
E
. Then press the Dark and Quiet buttons
simultaneously. The display shows (scrolling):
4
4
. If calibration does not automatically finish press
the Dark and Quiet buttons simultaneously to com-
plete calibration. The unit will beep twice and dis-
play shows, for example:
Note: In Combo Mode an “
H
H
” or “
C
C
” will be
shown to indicate mode of operation.
Important: If unit mounting is relocated in the
vehicle, (i.e., visor to windshield mounting or
dash mounting), or if the unit is moved to
another vehicle, you must recalibrate the com-
pass.
OPERATION
Reset Features
All user features can be reset to factory settings.
•Unplug the Power Cord from the unit.
•Press and hold the Power and Quiet buttons.
•Plug the Power Cord into the unit.
•Wait for 2 beeps.
•Release the Power and Quiet buttons.
Unit is now reset to the following features
and settings.
Default factory settings are:
1.
S1: (For Intellicord
®
) Power ON or OFF.
2. S2: (For Intellicord
®
) Quiet feature.
3. Combo Mode.
4. HIGHWAY Mode.
5. Dim/Dark Mode to full illumination of display.
6. Auto Quiet Mode OFF.
7. Safety Radar OFF.
8. Vehicle Battery Saver ON.
9. Full Power Up sequence.
10. Default TONE 3.
11. All Bands ON.
12. Laser ON.
13. POP ON.
14. Voice ON.
15.
LED Periscope to BLNK.
Intellicord
®
Ready
Using Whistler’s optional Intellicord
®
Power Cable
allows some models to control the detector’s fea-
tures such as Power On/Off, City Modes,
Dim/Dark, and Quiet/Auto Quiet with a simple
press of the button on the Power Cable. Two fea-
tures can be controlled: one by a short press of
the button, and the second by a long press of the
button. Option Mode allows the user to program
the feature assignments.
POP MODE ALERTS
14
15
16