Filter
Top Products
Mounting Guidelines
• Mount the unit as low as possible near the
center of the windshield.
• Do not mount the unit behind wipers,
ornaments, mirrored sunscreens, etc. These
obstructions have metal surfaces which can
affect radar and laser signals and reduce
critical warning time. (Regular tinted glass
does not affect reception).
• Some windshields have an Instaclear
™
or
Electriclear
™
type coating, which affect radar
signals. Consult your dealer or the owner’s
manual supplied with your vehicle to determine
if your windshield has this coating.
• Avoid placing the unit in direct contact with the
windshield.
• To reduce the possibility of theft, conceal your
unit when not in use.
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
: Make sure the unit is level
INSTALLATION
Windshield Mounting
• Install the two suction cups and rubber bumper
onto the bracket by fitting them into their holes.
• Press the suction cups onto the windshield at the
location you have chosen.
Important: Some newer cars have a plastic safety
coating on the inside of the windshield. The wind-
shield bracket may leave permanent marks on this
type of surface. To find out if your vehicle has this
type of windshield, check the owner’s manual or ask
your dealer. We recommend that you do not leave
the suction cup bracket on the window in direct sun-
light. If the detector is removed, this may cause
blistering of the dash in some vehicles.
• Slide the detector onto the bracket until it locks into
place.
• If necessary, the unit may be leveled by bending the
windshield bracket. Press the bracket release button
and remove the detector before bending.
Power Cord Connection
• Plug the small end of the power cord into the
unit’s power jack.
• Plug the large end into the vehicle’s cigarette lighter.
N
N
o
o
t
t
e
e
:
:
Cord fits tightly into detector. When
installing the cord, expect some resistance.
Fuse Replacement
The lighter socket plug is equipped with a
replaceable 2 amp 3AG fuse located behind the
silver tip. To replace the fuse, carefully unscrew
the tip of the plug.
I
I
m
m
p
p
o
o
r
r
t
t
a
a
n
n
t
t
:
:
Unscrew slowly. The tip contains a
spring which may fly out when disassembling.
Insert the new fuse with the spring and screw on
the tip. With use, screw cap on plug may loosen.
Retighten occasionally.
INSTALLATION CONT.
Windshield
Mounting
56
Rubber Bumper
OPERATION
7
Power On, Self Test
To turn the Power ON or OFF, push the center
of the Power/Volume button.
Each time your Whistler detector is turned on,
an automatic self-test sequence confirms that
the speaker and visual displays are functional.
• Display shows in order:
1. WHISTLER 2. X-band 3. K-band 4. Ka-band
5. LASER 6
.
.
SR OFF 7. VOICE ON 8.POP ON
9. B SVR ON 10.FILTER 11. HIGHWAY
Teach/Tutorial Mode
Provides simulated alerts for each type of signal.
• Press City and Quiet buttons simultaneously
• Display Shows:
• Press Dark button to exit.
Setting Saver
Setting Saver saves your personalized settings
so that when the detector is turned off and then
on again, you do not have to re-enter them.
Featur
e Engaged Confirmation
Each time a button is pressed, one beep confirms
feature “on”, two beeps confirm feature “off”.
Integrated Real Voice
®
When selected, Real Voice
®
will be used to articu-
late the following:
1. Band Identification
2. Safety Warning System messages
3. Feature Selection
Note: In certain cases the voice message does not
replicate the text message.