Filter
Top Products
Power Connection
•
P
lug the small end of the power cord into the
unit’s power jack.
•
Plug the large end into the vehicle’s cigarette
l
ighter.
Fuse Replacement
The lighter socket plug is equipped with a replaceable
2
amp 3AG fuse located behind the silver tip. To
re
place the fuse, carefully unscrew the tip of the plug.
IMPORTANT:
Unscrew slowly. The tip
contains a spring which may fly out when
disassembling.
Insert the new fuse with the spring and
screw on the tip. With use, the screw cap on the
plug may loosen. Retighten it occasionally.
OPERATION
Power On Self Test & Volume
Each time your Whistler detector is turned on, an
automatic self-test sequence confirms that the
speaker and visual displays are functional. To
increase the volume, continue turning the
volume knob.
Integrated Real Voice
®
(XTR-335)
When selected, Real Voice
®
will be used to
articulate the following:
1. Band Identification
2. Safety Warning System messages
3. Feature Selection
Voice OFF/ON is selected by holding quiet
button for appr
oximately 2 seconds. V
oice ON
will announce "caution", V
oice OFF will give a
double beep.
INSTALLATION
Feature Engaged Confirmation
E
ach time a button is pressed, one beep confirms the
feature is “on”, two beeps confirm feature “off”.
Self Test Mute
Simply press the Quiet button during the self-test
s
equence to cancel the self-test audio. This will not
a
ffect radar/laser alerts. To
restore
the self-test audio,
s
imply press the Quiet button during the next self-test
.
Setting Saver (XTR-265/335)
Setting Saver saves your personalized settings so that
when the detector is turned off and then on again, you
do not have to re-enter them.
Auto Quiet Mode
Pressing QUIET before a radar signal is detected provides
an alternate alert pattern, consisting of four beeps
(indicating X, K, Ka or Safety Radar) followed by clicking.
The clicking will continue for as long as the detected signal
is present or any new signal is detected within 20 seconds,
becoming more rapid as the strength of the signal
increases.
• Press Quiet (before a signal is detected) to
engage Auto Quiet.
• Once the Auto Quiet mode is engaged, you
may cancel the audio alarm by pressing Quiet.
• Press Quiet (when the unit is not alarming) to
cancel Auto Quiet mode.
Quiet Mode
Pressing Quiet cancels the audio during an alert and
any new alert within 20 seconds. After approximately
20 seconds, 2 beeps are provided on any new alert,
and the unit then remains quiet.
• Press Quiet to cancel the audio.
• Press Quiet a second time during an alert to restore the
standard audio alert pattern; or turn the unit off, then on.
OPERATION
City/City I/City II Mode
W
histler’s Three Stage City Mode is designed to
reduce the annoyance of automatic door openers,
intrusion alarms and other devices which share
f
requencies with police radar. Generally, X band is
used for these devices.
• Press City button to cancel Highway mode and
e
ngage City Mode. The display will switch fr
om
“
H
H
” to “
C
C
”.
• Press City button again to enter City
I
I
Mode.
•
Press City button again to enter City
I
I
I
I
M
ode.
N
N
o
o
t
t
e
e
: After 3 seconds, “
I
I
” or “
I
I
I
I
” City Mode
indicator turns off on the XTR-145.
• Pressing City button a fourth time cancels City
I
I
I
I
Mode and returns the unit to Highway
Mode.
In City Mode, weak speed/safety radar signals
give an initial alarm of two beeps, and then
remains quiet unless the signal becomes very
strong. When the signal strength increases, two
additional beeps are provided. City
I
I
and City
I
I
I
I
Modes operate the same as Highway Mode, but
in City
I
I
Mode, only the X band sensitivity is
lowered. In City
I
I
I
I
Mode, X-band is not detected.
Caution: Some towns/small cities may still be
using X band radar. City Modes do not change
the audio alert for laser or VG-2.
Highway Mode
Highway mode provides full audio warnings any time
radar (X, K, Ka, Safety Radar) or laser signals ar
e
detected, and is recommended for open road driving.
OPERATION
8910