Filter
Top Products
WARRANTY (U.S.A.)
Spin Master Ltd. warrants to the original consumer purchaser, that this product is thoroughly tested and
inspected before shipment and is guaranteed to be free of factory defects in materials and workmanship for thirty
(30) days (unless specified in alternate warranties) from the date of purchase.
In the event of such a defect within the warranty period, Spin Master Ltd., at our sole option, will repair or
replace the product or provide you with another product of equal value. Repair or replacement shipment is free of
charge. Shipping replacement may take 2 to 6 weeks, depending on customer’s location.
In the event of a defect covered under this warranty, please call the toll-free number listed below. Many
problems can be solved in this manner. If necessary, you will be instructed to return the defective part or unit,
packed securely, postage prepaid and insured by the customer, to the address below. Enclose your name, address,
dated sales receipt, and a brief explanation of the defect. There may be an additional handling charge if you send
the entire toy.
The warranty is valid if and only if the product has been operated in accordance with the instructions. This
warranty does not cover worn or defective batteries, damage resulting from neglect, unauthorized modification, acci-
dent, misuse, abuse, any action or omission which constitutes a deviation from the instructions or from the use of
accessories or parts not manufactured by Spin Master Ltd. If the product is returned without a dated sales receipt
the product is excluded from coverage under this warranty.
Spin Master Ltd.’s liability for defects in material and workmanship under this warranty shall be limited to repair
or replacement, at our sole option, and in no event shall we be responsible for accidental, consequential. or
contingent damages (except in those states that do not allow this exclusion or limitation) or refunds. This warranty is
exclusive, and is made in lieu of any express or implied warranty. This warranty is valid only for products sold in the
U.S.A. This warranty gives you specific legal rights and you may have other rights, which vary from state to state.
Some states do not allow the exclusion of incidental or consequential damages, so the above exclusions or limita-
tions may not apply to you.
Spin Master Ltd. reserves the right to improve the design of any product without assuming any obligation to
modify any product previously manufactured.
If you need assistance, please contact our Customer Care Center (below) for help.
SPIN MASTER LTD.
CUSTOMER CARE CENTRE
450 Front Street West
Toronto, Ontario M5V 1B6 CANADA
TOLL-FREE NUMBER 1-800-622-8339
(valid only in North America)
Hours: 8:00 A.M. – 5:00 P.M.
Eastern Time: Monday – Friday.
Air Hogs TM is a trademark of Spin Master Ltd.
© 2003 Spin Master Ltd. All rights reserved.
Produced under license from Boeing Management Company.
Delta and Boeing are among the trademarks owned by Boeing.
Manufactured for and distributed by Spin Master Ltd.
MADE IN CHINA
Item #45044 REV 4 U.S. English
TM
TROUBLE SHOOTING GUIDE
PROBLEM
SOLUTIONCAUSE
ROCKET does not
launch.
1. No air in LAUNCHER/
ACCUMULATOR.
1. Use the PUMP HANDLE and pump 15 times before
pulling the LAUNCH RELEASE HANDLE.
2. LAUNCHER/ACCUMULATOR is
not positioned on a level surface.
2. Re-adjust the LAUNCHER LEGS and make sure
that the LAUNCHER is sitting on a level surface. If
the LAUNCHER is tilted more than 15° to any side,
the rocket WILL NOT LAUNCH.
3. AIR TUBING and/or CONNECTORS
are not completely straight.
3. Ensure that all CONNECTORS are securely
fastened, and that the AIR TUBING is in a straight
line with the PUMPING STATION before launching.
4. CONNECTORS on AIR TUBING
not properly assembled/tightened.
4. Unscrew each CONNECTOR and repeat Step 6
in the “Preparing to Launch” section. Remember
to tighten any loose cable before screwing the
CONNECTORS together.
5. LAUNCHER SHAFT not locked in
place for launch.
5. Push the LAUNCHER SHAFT down until
it
CLICKS.
6. LAUNCHER SHAFT is JAMMED.
6. The LAUNCHER SHAFT may have become
jammed if it was pushed TOO HARD when you
tried to
CLICK it into position for launch. To un-jam
it, 1. ASK AN ADULT FOR HELP. 2. Raise up the
3 LAUNCHER LEGS, 3. remove ROCKET from
launcher shaft, 4. have the child pull on the
LAUNCH RELEASE TRIGGER at the same time
as the ADULT pulls up on the LAUNCHER SHAFT
to un-jam it.