Filter
Top Products
1413
ADJUSTMENT OF CHAIR
Before sitting on the massage chair
OR
(Remote control) (Sensor controller)
Raise the back rest, and
lower the foot rest by
continuously pressing
the UP ( ) button.
Recline the back rest, and
raise the foot rest by
continuously pressing
the DOWN ( ) button.
Do not attempt to recline the back rest deeply at first (until the body is accustomed to massaging),
so that the massage force may be too strong.
Be sure to check that there is no-one or any pets around the massager prior to adjusting the back
rest. It may result in an accident or injury.
While massaging the legs, do not attempt to recline the back rest when the legs are squeezed by
the air bags. Do not pull the legs out forcibly, this may result in injury to the legs.
NOTE
Head cover
5
Adjust the angle of the back rest.
The back rest and foot rest are moved in conjunction with each other.
Adjustment range
Approx. 50
120
Adjustment range Approx. 90
Back rest
Foot rest
1
Sit on the center of massage chair.
Center of the chair
Foot rest
2
Adjust the position of head cover.
4
Press ZERO-G button to move the back rest,
foot rest, and the seat to achieve the desired
reclining position.
ZERO-G 1 (Zero gravity position 1)
Posture suited for whole body massaging
ZERO-G 2 (Zero gravity position 2)
Posture suited for lower body massaging
ZERO-G 1
(Slow flickering)
ZERO-G 2
(Rapid flickering)
Back rest
Foot rest
Hook-and-
loop fasteners
When the button is pressed, the lamp of the remote control
illuminates and the sole warmer will turn on.
When the foot rest is fully lowered, the foot rest will rise a little.
When the massaging rollers are not located in the upper section,
the massaging rollers will move to the upper section and stop.
(During the movement, the characters of "ORIGIN" on the remote
control flicker.)
3
Press the OPERATION ON/OFF button.
Press
Press
Adjust the attaching position with
hook-and-loop fasteners.
During the massage, adjust the head
cover not to touch the shoulders.
Do not attempt to climb onto or off the seat
by stepping on the foot rest. Do not attempt
to place anything upon or sit on the foot rest. The
user may fall over, resulting in an accident
or injury.
NOTE
For safety, check the position of the
massaging rollers before leaning slowly
back on the massager. Do not twist the
body, but lean straight back on the
massager, so that the massaging rollers
are in position on either side of the spine.
CAUTION
Sit deeply in the massage chair so that the
waist touches the back rest.
Bring all parts of the massage chair to
their home position by pressing the
HOME POSITION button.
Sitting on the massage chair while the foot rest is being raised
is dangerous. Be sure to lower the foot rest completely before
sitting on the massage chair.
The chair will be automatically brought to its home position by
pressing the HOME POSITION button.
Reclining positions change automatically at each press of the button.
(Button illuminates while reclining and flickers when in position)
Keep the RECLINING button pressed until the desired angle is achieved.
When adjusted at ZERO-G, the seat is lowered together with the above mentioned movement.
(It is not possible to adjust only the seat.)
For the sake of safety, if the UP ( ) button is pressed with the seat raised, the foot rest may be raised
briefly before going down.
Automatically starts massaging in Air
Course (Massaging besides Air Course
cannot be selected)
When switched from ZERO-G 1 to 2, the foot rest is raised first, and moves to the set angle.
When switched form ZERO-G 2 to 1, the back rest is raised first, and moves to the set angle.
Reclining can be stopped during the reclining motion by pressing either the ZERO-G button, HOME POSITION
button, RECLINING button, FOOT REST button, OPERATION ON/OFF button, or STOP button.
When the reclining motion is stopped by pressing the STOP button, press the OPERATION ON/OFF button to
resume the operation.
When the reclining motion is stopped by pressing buttons other than the STOP button, press he desired button
for motion.
When back rest angle is adjusted from the ZERO-G 2, massaging other than Air Course can be selected.