Filter
Top Products
7
English
8
English
SETTING UP THE UNIT
WHERE TO USE THE UNIT
Keep at least 3.9 (10 cm) away from the wall.
Approx. 57.9
(147 cm)
Width
approx. 27.5
(70 cm)
Approx.
11.8 (30 cm)
Mat
Area where unit
touches the floor
Avoid places where the unit will be exposed to direct sunlight
for long periods of time or places where it will be exposed to
high temperatures, such as in front of a heater, etc., as this
can cause discoloration or hardening of the leather.
Placing a mat or cloth under the unit is recommended to
prevent floor damage. The size of the mat should be sufficient
[at least 42.1 in. × 27.5 in. (107 cm × 70 cm)] to cover the
areas where the unit touches.
Set the unit near the outlet.
See Warning No. 11 and 12 on page 1.
•
•
•
1 UNPACK THE UNIT AND RAISE THE BACKREST
CAUTION
When raising the backrest, be careful not to cause hands or feet to become caught between the backrest and the
backrest latch or the backrest and the armrests.
Failure to follow this precaution may result in injury.
•
Check that there
is nothing
around the unit.
Backrest latch
1
Remove the top of the shipping container.
When packed for shipping the backrest is folded forward.
2
Remove the packing and cushioning
materials and take out all accessories.
3
Raise the backrest.
Do not connect the power cord to an electrical outlet during setup.
Hold the backrest with both hands and lift in the direction of the
arrow until it comes to a stop.
Be careful the power cord and controller are not caught in the
backrest.
•
•
•
•
2 INSPECT CONTENTS OF SHIPPING CONTAINER
Massage Lounger Pillow Back Cushion Allen Key — 1
Attachment Screws — 8
Lock Switch Key — 1
The lock switch key has
been inserted in the
lock switch prior to
leaving the factory.
•
Armrests — 2
3 HOW TO MOVE THE UNIT
Using the wheels to move the unit
Hold the backrest to move the unit when using the wheels.
It is easier to move the unit with the massage heads
retracted and the backrest in the upright position.
* Place a mat or cloth on the floor and move the unit slowly
to prevent floor damage.
•
•
Lifting the Unit
Move the unit by having 2 persons hold the armrests.
* Please hold the armrests securely to avoid dropping the
unit as it may damage your floor.
•
Move it slowly
Wheels
4 INSTALL THE ARMRESTS ON THE UNIT
Front
Back
Left
Velcro
Zipper
Convex
Front Rear
Round hole
1
Install the armrests.
1 Unfasten the velcro.
2 Unzip the zipper of the armrest completely.
3 Make sure to confirm the side (left or right) and
direction (front or back) for each armrest.
The illustration shows the left armrest. The right armrest
is stamped “Front”, “Right” and “Back”.
* The left armrest must be installed on the left hand side of
the unit.
4 Align the proper armrest with the unit and connect.
Be careful not to catch the fabric between the chair
and the armrest.
Lift up
Secure with screws
Allen key
2
Secure the armrests with attachment
screws.
(Total of 4 positions for a single armrest)
Lift the fabric on the side of the armrest and insert the
attachment screw onto the end of the Allen key, and
then tighten.
(Tighten the screws in the 4 positions lightly at first, and
then tighten all screws firmly.)
* If the screw does not enter into the hole, tighten the screw
by pushing the armrest from the top.
3
Close the zipper at the bottom side of
the armrests.
When closing the zipper, be careful not to twist the end of
the zipper.
1 Set the velcro.
2 Zip the zipper.
4
Put both ends of the zipper into the
inside.
1 Turn in the edge of the zipper.
2 Fix the sliding tab of the zipper with the velcro.
7-8 2008/02/20 18:12:35