Filter
Top Products
The following abbreviations are used to represent values for Control Module Pin-Out data
I Input SG Sensor Ground S SCP Network V Voltage (DC)
O Output A ACP Network D Serial and Encoded Data Hz Frequency
SS Sensor Supply V C CAN (Network) B+ Battery Voltage kHz Frequency x 1000
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation. THIS INFORMATION SHOULD BE USED FOR
REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all components
connected and fitted. “Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, grounds, control
modules and control module pins.
DATE OF ISSUE: September 2000
Fig. 04.1
COMPONENTS
Component Connector / Type / Color Location / Access
AIR ASSIST CLOSE VALVE PI29 / 3-WAY SUMITOMO SS / GREY THROTTLE ASSEMBLY
BRAKE SWITCH CC40 / 4-WAY MULTILOCK 070 / WHITE ADJACENT TO THE BRAKE PEDAL MOUNTING ASSEMBLY
CCV: CANISTER CLOSE VALVE CV1 / 2-WAY YAZAKI 90 / BLACK UNDER VEHICLE / RH REAR
CKPS: CRANKSHAFT POSITION SENSOR PI17 / 2-WAY ECONOSEAL III HC / BLACK ENGINE / REAR OF BED PLATE
CMPS: CAMSHAFT POSITION SENSOR – ‘A’ BANK PI16 / 2-WAY YAZAKI / BLACK ENGINE COMPARTMENT / ‘A’ BANK CYLINDER HEAD, REAR
CMPS: CAMSHAFT POSITION SENSOR – ‘B’ BANK PI15 / 2-WAY YAZAKI / BLACK ENGINE COMPARTMENT / ‘B’ BANK CYLINDER HEAD, REAR
ECM AND TCM COOLING FAN EM66 / 2-WAY MULTILOCK 070 / WHITE ENGINE COMPARTMENT / CONTROL MODULE ENCLOSURE
ENGINE CONTROL MODULE EM80 / 31-WAY AMP 403 / NATURAL ENGINE COMPARTMENT / CONTROL MODULE ENCLOSURE
EM81 / 24-WAY AMP 403 / NATURAL
EM82 / 17-WAY AMP 403 / NATURAL
EM83 / 28-WAY AMP 403 / NATURAL
EM84 / 22-WAY AMP 403 / NATURAL
EM85 / 12-WAY MULTILOCK 070 / WHITE
ECTS: ENGINE COOLANT TEMPERATURE SENSOR PI4 / 2-WAY ECONOSEAL E J2 / GREY ENGINE COMPARTMENT / REAR OF ENGINE TOP HOSE
EOTS: ENGINE OIL TEMPERATURE SENSOR PI38 / 2-WAY ECONOSEAL EC J2 / GREY ENGINE BLOCK / BELOW GENERATOR
EVAPP: EVAP CANISTER PURGE VALVE EM39 / 2-WAY ECONOSEAL J2+ / BLACK ENGINE COMPARTMENT / BULKHEAD
FTPS: FUEL TANK PRESSURE SENSOR FP1 / 3-WAY ECONOSEAL III LC / BLACK TOP OF FUEL TANK / TRUNK CARPET
HO2S: HEATED OXYGEN SENSOR (DOWNSTREAM) – ‘A’ BANK EM22 / 2-WAY SUMITOMO 0902 / BLACK ENGINE COMPARTMENT / BRACKET ON TOP OF TRANSMISSION
HO2S: HEATED OXYGEN SENSOR (DOWNSTREAM) – ‘B’ BANK EM24 / 2-WAY SUMITOMO 0902 / BLACK ENGINE COMPARTMENT / BRACKET ON TOP OF TRANSMISSION
HO2S: HEATED OXYGEN SENSOR (UPSTREAM) – ‘A’ BANK EM21 / 4-WAY SUMITOMO 0902 / GREY ENGINE COMPARTMENT / BRACKET ON TOP OF TRANSMISSION
HO2S: HEATED OXYGEN SENSOR (UPSTREAM) – ‘B’ BANK EM23 / 4-WAY SUMITOMO 0902 / GREY ENGINE COMPARTMENT / BRACKET ON TOP OF TRANSMISSION
KS: KNOCK SENSOR – ‘A’ BANK PI26 / 2-WAY ECONOSEAL III LC / BLACK ENGINE VEE / UNDER INTAKE MANIFOLD
KS: KNOCK SENSOR – ‘B’ BANK PI27 / 2-WAY ECONOSEAL III LC / BLACK ENGINE VEE / UNDER INTAKE MANIFOLD
MAFS: MASS AIR FLOW SENSOR PI35 / 5-WAY YAZAKI 92 / BLACK ENGINE COMPARTMENT / REARWARD OF AIR CLEANER
PARKING BRAKE SWITCH CC11 / 2-WAY MULTILOCK 040 / BLACK CENTER CONSOLE ASSEMBLY
PPS: PEDAL POSITION SENSORS PI42 / 5-WAY SUMITOMO TS090 / BLACK ENGINE COMPARTMENT / ON THROTTLE ASSEMBLY
THROTTLE MOTOR PI33 / 2-WAY SUMITOMO HM250 / BLACK ENGINE COMPARTMENT / THROTTLE ASSEMBLY
TPS: THROTTLE POSITION SENSORS PI6 / 4-WAY ECONOSEAL J2T / BLACK ENGINE COMPARTMENT / ON THROTTLE ASSEMBLY
VVT SOLENOID VALVE – ‘A’ BANK PI31 / 2-WAY YAZAKI 0902 / BLACK ENGINE COMPARTMENT / ‘A’ BANK CYLINDER HEAD / FRONT
VVT SOLENOID VALVE – ‘B’ BANK PI32 / 2-WAY YAZAKI 0902 / BLACK ENGINE COMPARTMENT / ‘B’ BANK CYLINDER HEAD / FRONT
RELAYS
Relay Case Color Connector / Color Location / Access
THROTTLE MOTOR POWER RELAY BROWN EM49 / BROWN CONTROL MODULE ENCLOSURE RELAYS / ENGINE COMPARTMENT
O2S HEATERS RELAY BROWN EM75 / BROWN CONTROL MODULE ENCLOSURE RELAYS / ENGINE COMPARTMENT
HARNESS-TO-HARNESS CONNECTORS
Connector Type / Color Location / Access
BT4 54-WAY THROUGH PANEL / GREY BELOW PARCEL SHELF / TRUNK / REAR BULKHEAD / RH SIDE
BT5 3-WAY MULTILOCK 070 / WHITE TOP OF FUEL TANK / TRUNK CARPET
CA19 20-WAY MULTILOCK 070 / YELLOW LH ‘A’ POST CONNECTOR MOUNTING BRACKET / LOWER ‘A’ POST FINISHER
CV2 3-WAY MULTILOCK 070 / WHITE UNDER REAR SEAT
EM1 12-WAY AUGAT 1.6 / BLACK ENGINE COMPARTMENT / ADJACENT TO ABS PUMP
EM2 20-WAY MULTILOCK 070 / GREY PASSENGER ‘A’ POST / LOWER ‘A’ POST FINISHER
EM3 18-WAY MULTILOCK 070 / WHITE PASSENGER ‘A’ POST / LOWER ‘A’ POST FINISHER
EM53 20-WAY MULTILOCK 070 / WHITE PASSENGER ‘A’ POST / LOWER ‘A’ POST FINISHER
FC1 54-WAY THROUGH PANEL CONNECTOR / GREY BELOW PASSENGER SIDE AIR VENT / GLOVE BOX ASSEMBLY
LF3 54-WAY THROUGH PANEL CONNECTOR / GREY LH ‘A’ POST / LOWER ‘A’ POST FINISHER
PI1 57-WAY SUMITOMO TS090 / BLACK ENGINE COMPARTMENT / BULKHEAD / REAR OF ENGINE
PI2 13-WAY ECONOSEAL III LC / BLACK ENGINE COMPARTMENT / BRACKET ON TOP OF TRANSMISSION
GROUNDS
Ground Location / Type
EM8L EYELET (PAIR) – EMS LH GROUND STUD
EM16L EYELET (PAIR) – EMS BULKHEAD GROUND STUD
EM16R EYELET (PAIR) – EMS BULKHEAD GROUND STUD
FOR CONTROL MODULE PIN OUT INFORMATION, UNFOLD PAGE TO LEFT.
CONTROL MODULE PIN OUT INFORMATION
ENGINE CONTROL MODULE
Pin Description Active Inactive
O EM80-01 EVAP VALVE ACTIVATE GROUND (VALVE OPEN) B+
O EM80-02 CANISTER CLOSE VALVE ACTIVATE GROUND B+
I EM80-03 GROUND (POWER) GROUND GROUND
O EM80-04 THROTTLE MOTOR POWER SUPPLY B+ GROUND
O EM80-05 THROTTLE MOTOR POWER SUPPLY B+ GROUND
O EM80-06 THROTTLE MOTOR POWER SUPPLY B+ GROUND
O EM80-07 THROTTLE MOTOR POWER SUPPLY B+ GROUND
I EM80-08 THROTTLE MOTOR POWER SUPPLY B+ GROUND
I EM80-09 THROTTLE MOTOR POWER SUPPLY B+ GROUND
I EM80-15 EOT SIGNAL 2.5 V @ 34 °C; 0.5 V @ 90 °C; (DECREASING VOLTAGE WITH TEMPERATURE INCREASE)
D EM80-17 SERIAL COMMUNICATIONS
D EM80-18 SERIAL COMMUNICATIONS
D EM80-19 ECM PROGRAMMING
I EM80-21 GROUND (THROTTLE MOTOR 1) GROUND GROUND
D EM80-27 ECM PROGRAMMING
I EM80-29 GROUND (LOGIC 2) GROUND GROUND
I EM80-31 GROUND (THROTTLE MOTOR 2) GROUND GROUND
O EM81-01 VARIABLE VALVE TIMING SOLENOID + ‘A’ BANK B+ (12% DUTY CYCLE @ IDLE) (INCREASING WITH ADVANCE) GROUND
O EM81-02 VARIABLE VALVE TIMING SOLENOID – ‘A’ BANK GROUND GROUND
O EM81-03 EMS CONTROLLED RELAY ACTIVATE GROUND B+
O EM81-06 VARIABLE VALVE TIMING SOLENOID + ‘B’ BANK B+ (12% DUTY CYCLE @ IDLE) (INCREASING WITH ADVANCE) GROUND
O EM81-07 VARIABLE VALVE TIMING SOLENOID – ‘B’ BANK GROUND GROUND
I EM81-08 GROUND (POWER) GROUND GROUND
I EM81-09 PEDAL POSITION SIGNAL (PPS/1) 0.6 V = FOOT OFF; 3.8 V = PEDAL FULLY DEPRESSED
I EM81-10 TPS SIGNAL (TPS/1) 0.5 V = IDLE; 4.75 V = WOT
I EM81-12 PARK / NEUTRAL CONFIRMATION B+ (P, N) GROUND (R,D,4,3,2)
I EM81-16 FUEL TANK PRESSURE SENSOR SIGNAL 4.9 V = LOW PRESSURE, 0.2 V = HIGH PRESSURE
I EM81-17 EMS SWITCHED POWER SUPPLY 1 B+ 0 V
I EM81-18 PEDAL POSITION SIGNAL (PPS/2) 0.8 V = FOOT OFF; 2.4 V = PEDAL FULLY DEPRESSED
I EM81-19 TPS SIGNAL (TPS/2) 0.6 V = IDLE; 4.85 V = WOT
I EM81-21 GROUND (LOGIC 1) GROUND GROUND
I EM81-22 PARKING BRAKE SWITCH GROUND (APPLIED) B+
SG EM81-24 PEDAL POSITION / THROTTLE POSITION SENSORS SHIELD GROUND GROUND
SS EM82-01 SENSOR SUPPLY VOLTAGE 1 5 V 5 V
I EM82-02 ENGINE CRANK GROUND (CRANKING)
I EM82-04 HO2S, UPSTREAM ‘A’ BANK – VARIABLE CURRENT (µA) 3.5 V
I EM82-05 HO2S, UPSTREAM ‘B’ BANK – VARIABLE CURRENT (µA) 3.5 V
O EM82-06 THROTTLE MOTOR POWER RELAY ACTIVATE GROUND B+
SG EM82-07 SENSORS SIGNAL GROUND 1 GROUND GROUND
I EM82-08 BRAKE SWITCH GROUND B+
I EM82-09 IGNITION SWITCHED POWER SUPPLY B+ B+
SS EM82-10 HO2S, UPSTREAM ‘A’ BANK – CONSTANT 3.8 V
SS EM82-11 HO2S, UPSTREAM ‘B’ BANK – CONSTANT 3.8 V
I EM82-12 INERTIA SWITCH ACTIVATED (VEHICLE IMPACT) GROUND B+
I EM82-13 EMS SWITCHED POWER SUPPLY 2 B+ 0 V
I EM82-14 ECT SIGNAL 0.41 V @ 90 °C (DECREASING VOLTAGE WITH TEMPERATURE INCREASE)
D EM82-15 OK TO START ENCODED COMMUNICATIONS
D EM82-16 SECURITY ACKNOWLEDGE ENCODED COMMUNICATIONS
I EM82-17 IATS SIGNAL 0.98 V @ 10 °C (DECREASING VOLTAGE WITH TEMPERATURE INCREASE)
O EM83-03 AIR ASSIST CLOSE VALVE ACTIVATE 8 V @ IDLE (78% DUTY CYCLE)
SS EM83-05 SENSOR SUPPLY VOLTAGE 2 5 V 5 V
SG EM83-06 SENSOR SHIELD GROUND GROUND
SG EM83-07 CKPS SIGNAL GROUND GROUND GROUND
I EM83-08 CKPS SIGNAL 5 V @ 1000 RPM = 45 Hz; 2000 RPM = 90 Hz
SG EM83-09 CMPS, ‘A’ BANK SIGNAL GROUND GROUND GROUND
SG EM83-12 HO2S SHIELD GROUND GROUND
SG EM83-13 SENSORS SIGNAL GROUND 2 GROUND GROUND
I EM83-14 KNOCK SENSOR, ‘A’ BANK SIGNAL 0 kHz = NO KNOCK, 2 – 20 kHz = KNOCK
C EM83-15 CAN NETWORK 15 – 1500 Hz
C EM83-16 CAN NETWORK 15 – 1500 Hz
SG EM83-17 CMPS, ‘B’ BANK SIGNAL GROUND GROUND GROUND
I EM83-18 CMPS, ‘B’ BANK SIGNAL 0.7 – 1 VAC @ 1000 RPM = 43 Hz; 2000 RPM = 72 Hz
I EM83-19 CMPS, ‘A’ BANK SIGNAL 0.7 – 1 VAC @ 1000 RPM = 43 Hz; 2000 RPM = 72 Hz
I EM83-20 BATTERY POWER SUPPLY B+ B+
I EM83-21 HO2S, ‘A’ BANK DOWNSTREAM 0.1 – 0.9 V @ IDLE (SWING)
I EM83-22 HO2S, ‘B’ BANK DOWNSTREAM 0.1 – 0.9 V @ IDLE (SWING)
I EM83-23 KNOCK SENSOR, ‘B’ BANK SIGNAL 0 kHz = NO KNOCK, 2 – 20 kHz = KNOCK
C EM83-24 CAN NETWORK 15 – 1500 Hz
C EM83-25 CAN NETWORK 15 – 1500 Hz
SG EM83-26 MAFS REFERENCE GROUND GROUND GROUND
SG EM83-27 MAFS REFERENCE GROUND GROUND GROUND
I EM83-28 MAFS SIGNAL 1.2 V @ IDLE, INCREASING WITH RPM INCREASE
I EM84-01 GROUND (DOWNSTREAM HO2S HEATERS) GROUND GROUND
O EM84-07 HO2S HEATER, ‘A’ BANK DOWNSTREAM CONTROL GROUND (20 – 60% DUTY CYCLE) B+
O EM84-15 HO2S HEATER, ‘B’ BANK DOWNSTREAM CONTROL GROUND (20 – 60% DUTY CYCLE) B+
I EM84-16 GROUND (INJECTORS 1A, 2B, 3B, 4A) GROUND GROUND
I EM84-22 GROUND (INJECTORS 1B, 2A, 3A, 4B) GROUND GROUND
O EM85-01 HO2S HEATER, ‘A’ BANK UPSTREAM CONTROL GROUND (85 – 90% DUTY CYCLE AT IDLE) B+
O EM85-02 HO2S HEATER, ‘B’ BANK UPSTREAM CONTROL GROUND (85 – 90% DUTY CYCLE AT IDLE) B+
O EM85-05 “COOL BOX” COOLING FAN ACTIVATE GROUND B+
I EM85-06 GROUND (HO2S A UPSTREAM HEATER) GROUND GROUND
I EM85-07 GROUND (HO2S B UPSTREAM HEATER) GROUND GROUND
I EM85-08 HO2S HEATERS OBD MONITOR HEATERS ACTIVE = B+ V
NOTE: Refer to the Appendix at the rear of this book for CAN and SCP Network messages.