Filter
Top Products
TECHNICAL SPECIFICATIONS
Engine
Model Robin EX 13
Engine oil volume,
quarts/liters
0.6/0.6
Gasoline tank
volume, gal/liters
0.7/2.7
Type Air cooled, 4-cycle, single slant cylinder,
overhead camshaft, gasoline engine
Air fi lter Cyclonic type
Oil system Oil alert with auto shut down sensor
Muffl er Silent type 75 dbA, exhaust defl ector,
spark arrestor
Emissions Complies with EPA Phase 2 and CARB
Tier II USA regulations
Cooling Air cooled with internal and external
cooling fi ns
Cylinder Aluminum with cast iron liner
Controls Engine manual throttle, choke and fuel
shut off levers, manual on/off switch
Starting system Manual recoil starter with automatic
mechanical compression release and
zero kick back
Weight and Dimensions
Weight – dry, lbs/kg 84/38
Weight with gasoline and oil full, lbs/kg 91/41
Length (handle folded in), inch/mm 34/864
Width, inch/mm 19/483
Height, inch/mm 21/533
CALIFORNIA AIR RESOURCES BOARD (CARB): This machine is considered a preempt Off-Road Application as relating to CARB stan-
dards. Under construction equipment, and in particular, as a Saws : concrete, masonry, cutoff, with engine power less than 19KW (25hp),
CARB standards do not apply to this machine.
For more information see the website http://www.arb.ca.gov/msprog/offroad/preempt.htm
EC DECLARATION OF CONFORMITY
Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna Soff-Cut 150
dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), complies with
the requirements of the COUNCILíS DIRECTIVE:
• of May 17, 2006 ”relating to machinery” 2006/42/EC
• of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.
• of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.
The following standards have been applied: EN ISO 12100:2003, EN 55014-1:2006, EN 55014-2/A1:2001, EN 61000-3-2:2006, EN 61000-
3-3/A1/A2:2005, EN 13862/A1:2009.
Huskvarna December 29, 2009
Henric Andersson
Vice President, Head of Power Cutters and Construction Equipment
(Authorized representative for Husqvarna AB and responsible for technical documentation.)
TECHNICAL DATA
Blade
Material cut Green concrete only
Blade type 6.0 inch (152 mm) dry cut with tri-arbor
Blade rotation Counter clockwise, upcutting
Blade shaft speed,
rpm
4450
Cutting depth 1 to 1 3/16” (25 to 30 mm) depending
on amount of blade wear.
Cutting distance
from wall, inch/mm
3/76
Average cutting rate - Estimate only. Speed will vary with job
conditions and concrete mixes.
Soft aggregates, ft/min / m/min 12/3,7
Medium aggregates, ft/min / m/min 8/2.4
Hard aggregates, ft/min / m/min 4/1.2
Noise emissions (see note 1)
Sound power level, measured dB(A) 98
Sound power level, guaranteed dB(A) 99
Sound levels (see note 2)
Sound pressure level at the operators ear, dB(A) 84
Vibration levels, a
hv
(see note 3)
Handle right, m/s
2
7,9
Handle left, m/s
2
7,8
Note 1: Noise emissions in the environment measured as sound
power (L
WA
) in conformity with EC directive 2000/14/EC.
Note 2: Noise pressure level according to EN 13862. Reported
data for noise pressure level has a typical statistical dispersion
(standard deviation) of 1.0 dB(A).
Note 3: Vibration level according to EN 13862. Reported data for
vibration level has a typical statistical dispersion (standard devia-
tion) of 1 m/s
2
.