Filter
Top Products
Controls and Features
KA
|
X
|||
Here ExpertMeter shows 1 weak Ka-
band signal, and 3 weak X-band signals.
X
On very weak signals, there will not
be a vertical line at all. This shows a very
weak X-band signal.
ExpertMeter Details
The band designators (X, K, Ka) will
stay on the display for a few seconds after
the signal has passed. This allows you to see
what the unit detected, even on very brief
signals.
However, the vertical lines representing
individual signals continuously change
(several times a second) to give you a
continuous view of the signal strength of all
radar signals present.
SpecDisplay
Passport’s new SpecDisplay option is also
designed for the advanced detector user. In
this mode, Passport will display the actual
numeric radar frequency being received.
K 24.150
Display shows a K-band signal at
24.150 GHz
Ka34.700
Display shows a Ka-band signal at
34.700 GHz
X 10.525
Display shows an X-band signal at
10.525 GHz
Note: Even long-time detector users will
require a significant amount of time to
get familiar with this new level of
information.
Optional
ZR3 Laser Shifter
™
Configuration
Your Passport SR7 is fully compatible with
Escort’s ZR3 Laser Shifter. Once added, the
integrated Shifters add a new level of laser
defense to your SR7 remote – making it the
ultimate defense against laser guns.
Once the Laser Shifter’s have been
connected to Passport’s Interface, the
internal computer will automatically make
changes to the “Bands” programming
options. Under the “Laser” option, the
Shifters can now be programmed to
receive only, or “Shift” (default once
connected), an incoming laser signal. Also,
during the start-up sequence, the SR7 will
acknowledge the new configuration.
During a laser alert, the display will
show “Front” “Lsr Shft” when a signal is
received from the front, or “Rear” “Lsr Shft”
when a signal is received from the rear. This
message will be accompanied by the normal
Laser alert tone.
For more information on the Laser
Shifter ZR3, consult your 12-volt retailer.
8 9
How to customize Passport with EZ-Programming
There are 9 user-selectable options so you
can customize your Passport for your own
preferences. The buttons that are normally
used for CITY and MUTE are used to enter
the Program Mode, to REVIEW your current
program settings, and to CHANGE any
settings as desired. Pages11-13 explain each
option in more detail.
How to use EZ-Programming
To enter Program Mode, press both
buttons and hold for 2 seconds.
(Passport will beep twice and display
“Program.” (Brightness is at maximum
during programming.)
Then press the REVIEW button to review
the current settings. (You can either tap
the button to change from item to item, or
hold the button to scroll through the items.)
Press the CHANGE button to change
any setting. (You can either tap the button
to change from setting to setting, or hold
the button to scroll through all the options).
To leave the Program Mode, simply wait
8 seconds without pressing any button.
(The unit will display “Complete,” beep 4
times, and return to normal operation.)
(To quickly return to all of the factory
defaults, press and hold the CITY and MUTE
buttons while turning on the unit.)
1
2
3
4
An example
For example, here’s how you would turn
Passport’s AutoMute feature off.
1 Enter the Program Mode by holding
both buttons down for 2 seconds. Passport
will beep twice and display
Program.
2 Press and hold the REVIEW button.
Passport will scroll through the categories,
starting with Display
Disp, then Pilot
Light
Pilot, then Power-on sequence
PwrOn , then Signal strength meter
Meter, then AutoMute aMute.
3 Release the REVIEW button when
Passport shows the AutoMute item. Since
the factory setting is for AutoMute to be
on, Passport will display
aMute ON.
(If you accidentally don’t release the
Review button in time, and Passport goes
to the next category, hold the Review
button down again, and after Passport
scrolls through all categories, it will begin
again at the top of the list.)
4 Press the CHANGE button to change
from
aMute ON to aMute OFF.
5 To complete the Programming, simply
wait 8 seconds without pressing any button.
Passport will display
Complete, beep 4
times, and return to normal operation.