Autostart AS-1795 Remote Starter User Manual


 
P. 2 ¸¬¬°æññ©©©ò¿«¬±-¬¿®¬ò½¿ Installation Guide
After selecting the function, press one of the corresponding buttons to select the option.
LOCK for Option 1;
UNLOCK for Option 2;
TRUNK for Option 3;
START for Option 4.
Ю±¹®¿³³·²¹ Ñ°¬·±²-
MODE 1 * indicates default setting
FUNCTION 1 – Ignition-controlled door locks
OPTION 1* Ignition lock disabled
OPTION 2 Ignition lock enabled
OPTION 3 Ignition unlock only
OPTION 4 Ignition lock only
FUNCTION 2 – Secure Lock
OPTION 1* Secure Lock disabled
OPTION 2 Secure Lock enabled in standard mode
OPTION 3 Secure Lock enabled in smart mode
FUNCTION 3 – Passive or Active Arming
OPTION 1* Passive arming (60 sec.)
OPTION 2 Active arming
OPTION 3 Passive arming (3 min.)
FUNCTION 4 – Door lock pulse timing
OPTION 1* 7/10-sec. lock/unlock pulses
OPTION 2 4-sec. Lock/Unlock pulses
OPTION 3 7/10-sec. Lock pulse and two ¼-sec. Unlock pulses
OPTION 4 1/10-sec. Lock/Unlock pulses
FUNCTION 5 – LED flashing
OPTION 1* Enabled (without starter kill will flash only when ignition is OFF)
OPTION 2 Disabled
OPTION 3 Enabled (with starter kill will flash when the starter kill engages.
This option should be selected ONLY if the starter kill is installed.)
MODE 2 * indicates default setting
FUNCTION 1 – Safe Start.
OPTION 1 Safe start enabled
OPTION 2* Safe start disabled
OPTION 3 “Swap Start” – enhanced safe start mode with extended safety:
To start the engine: press the LOCK and UNLOCK buttons simultaneously
To trigger AUX 2: press the START button
FUNCTION 2 – Engine Run Time
OPTION 1 Run Time = 3 minutes in gas mode / 8 minutes diesel mode
OPTION 2* Run Time = 15 minutes in gas mode / 20 minutes diesel mode
OPTION 3 Run Time = 25 minutes in gas mode / 30 minutes diesel mode
FUNCTION 3 – Idle Mode / Turbo Mode
OPTION 1 Idle Mode enabled / Turbo mode enabled
OPTION 2* Idle Mode enabled / Turbo mode disabled
FUNCTION 4 – Engine type and cold weather mode
OPTION 1 Diesel mode with 20-minute run time in cold weather mode (30 sec. delay)
OPTION 2* Gas mode with 3-minute run time in cold weather mode
OPTION 3 Diesel mode with 8-minute run time in cold weather mode (18 sec delay)
OPTION 4 Diesel mode with 8-minute run time in cold weather mode (7 sec delay)
FUNCTION 5 – Ignition Valet
OPTION 1 Ignition valet disabled
OPTION 2* Ignition valet enabled
MODE 3 * indicates default setting
FUNCTION 1 – Home Valet
TM
OPTION 1 Home Valet enabled
OPTION 2* Home Valet disabled
FUNCTION 2 – AUX 2 Programming
OPTION 1 Constant output while the LOCK and UNLOCK buttons are pressed.
In Safe Start Mode: activate AUX 2 by pressing the START button.
OPTION 2* Toggle ON/OFF (with 30-second timeout)
OPTION 3 Horn confirmation when lock.
OPTION 4 Priority Door Access
Installation Guide ¸¬¬°æññ©©©ò¿«¬±-¬¿®¬ò½¿ñ P. 7
Hood switch shutdown. With the vehicle running under the remote car starter, open the hood; the vehicle
should shut down. If it does not shut down, check the hood pin-switch and its connector.
Brake shutdown circuit. With the vehicle running under the remote car starter, press and release the brake
pedal. The engine should shut down immediately. If the engine continues to run, check the brake switch
connection.
Door locks and trunk testing. Make sure each of these options respond to the transmitter (if installed).
Starter kill option. Sit inside the vehicle with all doors closed. Arm the vehicle, then try to start the engine with
the key. They engine should not start. If the engine starts, rewire the starter kill to reach proper operation.
Valet mode. Make sure the remote car starter is able to properly enter and exit valet mode. When setting the
remote car starter into valet mode, pressing the lock button will lock the doors without activating the starter kill.
(Refer to the user guide for further information on valet mode.)
Idle mode. Make sure the vehicle properly enters and exits idle mode.
Most comebacks are the result of misunderstandings about how a product works or performs. Take the
time to properly explain all functions and features to the customers before they leave the premises.
Doing this will save time and money.