Filter
Top Products
Ó ß Ò Ë ß Ô ÌÎßÒÍÓ×ÍÍ×ÑÒ ÎÛÓÑÌÛ ÍÌßÎÌÛÎ
Ò±¬·½»
The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either
damage to the vehicle itself or to the unit. This unit must be installed by a certified technician using all safety devices supplied. Please
note that this guide has been written for properly trained Autostart technicians: a certain level of skills and knowledge is therefore
assumed. Please review the installation guide carefully before beginning any work.
É¿®²·²¹
This Remote Car Starter is designed for vehicles with a manual Transmission only. Before installing the Unit, test that the OEM Door
Switch contacts of the vehicle work well, and that the Parking Brake system operates properly.
DOC.1.02 – January 9, 2007 DL Lp Manufactured in Canada by Autostart
ßÍóïéçë
Ï«·½µ ײ-¬¿´´¿¬·±² Ù«·¼»
Ì¿¾´» ±º ݱ²¬»²¬-
ر© ¬± Ú´¿-¸ ¬¸» ر±¼ з²òòòòòòòòòòòòòòòòòòòòòòòï
Ì®¿²-³·¬¬»® Ю±¹®¿³³·²¹ Ю±½»¼«®»òòòòòï
Û²¬»®·²¹ Ю±¹®¿³³·²¹ Ñ°¬·±²-òòòòòòòòòòòòòòòï
Ю±¹®¿³³·²¹ Ñ°¬·±²-òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòî
Ì¿½¸ Ю±¹®¿³³·²¹òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòí
ر®² ر²µ Ì·³·²¹òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòí
λ-»¬¬·²¹ ¬¸» Ó±¼«´»òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòí
Í«°°´»³»²¬¿®§ ײº±®³¿¬·±²òòòòòòòòòòòòòòòòòòòòòê
Ú·º¬¸ λ´¿§ Ñ«¬°«¬ øî²¼ ×ÙÒô ßÝÝ ±®
ÝÎßÒÕ÷òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòê
Ì¿½¸ ¶«³°»® -»¬¬·²¹-òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòê
Ì»-¬·²¹òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòê
Ü·¿¹²±-¬·½- Š п®µ·²¹ Ô·¹¸¬ Ú´¿-¸
Ì¿¾´»òòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòòè
ر© ¬± Ú´¿-¸ ¬¸» ر±¼ з²
THE INSTALLER … THE MODULE …
Press and hold the hood pin for 4 seconds.
Release the hood pin. Parking Lights “ON”
While the parking lights are on, press down the hood pin once more
and release the hood pin immediately, before the parking lights turn off.
“ON” for 20 seconds
You now have 20 seconds to select one of the sub-menus
Ì®¿²-³·¬¬»® Ю±¹®¿³³·²¹ Ю±½»¼«®»
1. Flash the hood pin (see above) -- the parking lights will stay on for up to 20 seconds.
2. Before the lights go out, turn the ignition key to the IGNITION ON (RUN) position and immediately to the OFF position.
3. Press and hold the LOCK button and keep it down until the parking lights flash 5 times quickly.
4. The transmitter has been stored in memory.
5. To exit: close the hood.
To program a transmitter on the second vehicle for multi-car operation, you must press the TRUNK button (instead of LOCK
or UNLOCK) in step 3 of the transmitter programming procedure:
Û²¬»®·²¹ Ю±¹®¿³³·²¹ Ñ°¬·±²-
1. Flash the hood pin switch (see on page 1) the parking lights will stay on for up to 20 seconds.
2. Before the lights go out, press and hold the brake pedal and then press one of the following buttons:
LOCK ..................................................to access mode 1;
UNLOCK..........................................to access mode 2 or;
TRUNK................................................to access mode 3.
3. The parking lights will flash and the horn will honk (if programmed) once, twice or three times to confirm entry into a mode.
4. Release the brake pedal.
P. 8 ¸¬¬°æññ©©©ò¿«¬±-¬¿®¬ò½¿ Installation Guide
Ü·¿¹²±-¬·½- Š п®µ·²¹ Ô·¹¸¬ Ú´¿-¸ Ì¿¾´»
Flashes Description
1
Doors locked, starter kill armed.
Run time has expired.
TRUNK button pressed.
Start signal received by the module.
Cold weather mode cancelled.
2
Remote start attempt cancelled by remote.
Doors unlocked, starter kill disarmed.
Exiting ignition valet
Exiting remote valet
Power-up reset
3
Entering cold weather mode.
Entering ignition valet.
Entering remote valet.
Entering extended run time.
3 slow flashes… …after a failed start attempt The module did not detect a tach signal.
4
+12 V detected on the brake input wire either while cranking or during run time.
Entering multi-speed tach programming.
5 Slow Start attempt failed because no tach signal has been programmed.
5 Fast Tach signal programmed.
6 A remote start was attempted while a tach-before-crank signal was detected before cranking.
8 Unit reset see “Resetting the Module” (p.Error! Bookmark not defined.)
10 A ground (-) signal was detected on the hood pin input wire.
1 pause
1 pause
5 flashes
[During the
transmitter
programming
procedure]
Transmitter has been programmed.
1 – pause – 2
There was a remote start attempt while the vehicle was in valet mode.
Failed start: vehicle’s low battery voltage.
…followed by 1 flash Exiting cold weather mode ON SOLID for 3
seconds….
…followed by 3 flashes Entering cold weather mode
ON continuously
Idle mode: Idle mode is engaged
Run time: The vehicle has been remote started and is in run time.
ON continuously
While the brake
pedal is
pressed.
Confirms that cold weather mode is engaged
ON 2 seconds
The hood has been opened and a ground (-) signal has been detected on the hood pin input
wire.
ON 4 seconds Locking or unlocking a door (with Door pulses configured to 4 sec.)
ON 20 seconds The hood pin has been flashed and you are now in the programming centre.
Constant flashes
up to 25 sec.
Panic mode was triggered.
̱ ±¾¬¿·² ¿ ½±°§ ±º ¬¸» ·²-¬¿´´ ¹«·¼»ô °´»¿-» ª·-·¬ ¬¸»
¸¬¬°æññ©©©ò¿«¬±-¬¿®¬ò½¿ ©»¾-·¬» ¿²¼ ½´·½µ ±² ¬¸»
u ܱ©²´±¿¼ e ¬¿¾ò