Filter
Top Products
Page 5
128-7852
5 of 12
To do this:
1. Turn the ignition key on then off.
2. Within 10 seconds, press and release valet switch three times.
3. If the chirps were on before you started, then you will hear two chirps indicating they have
been turned off.
If the chirps were off before you started, then you will hear one chirp indicating they have been
turned on.
NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator and 3 chirp de-
fective zone indicator will always operate. Since these are important warnings to you that
something has happened, they cannot be eliminated.
NOTE: Your system must be programmed by the installation center to enable this feature.
RF SHOCK SENSOR MODE SELECTION
The way in which your alarm system reacts to threatening vibrations, created by attempts to enter
the vehicle by breaking a window, is adjustable by the transmitter immediately after arming. There
are 4 modes of operation that can be selected by the operator:
1. Normal Operation (default mode) In this mode, any strong vibrations will cause the siren
to sound (full detect) for 30 seconds. Any lesser vibration will cause the siren to emit about
6 short warn away chirps, (pre-detect).
2. Stage 1 (Omit pre-detect) In this mode, the warn away chirps created by the lesser vibration
will be deleted. If strong vibration occurs, the siren will sound.
3. Stage 2 (Omit pre & full detect) In this mode, both the pre-detect stage and the full trigger
stage of the sensor are defeated. The unit will not react to vibration of any magnitude.
4. Stage 3 (City Mode) In this mode, the pre-detect chirps will change from six pre-warning
tones to a full 10 seconds of warning chirps. The full detect trigger duration will be reduced
from 30 seconds to 15 seconds.
NOTE: Setting the stage of the shock sensor will be effective for one arming cycle only. Once
the system has been disarmed, the very next arming cycle will cause the sensor to
default to the normal operation stage.
To change or adjust the shock sensor, press and release the ARM button of you keychain
transmitter.
1. Within 2 seconds of arming, press and release the ARM button 1 time, to
defeat the pre-detect stage of the shock sensor. (The lights will flash and the
siren will chirp twice.)
2. Within 2 seconds of step 1, press and release the ARM button 2 times, to
defeat the pre and full detect stages of the shock sensor. (The lights will
flash and the siren will chirp three times.)
3. Within 2 seconds of step 1, press and release the ARM button 3 times to
enter the "City Mode" of operation. (The lights will flash and the siren will chirp four times.)
While under control of the remote start the system can be programmed to allow you to shunt the
shock sensor from the transmitter. If the system has been such programmed, simply press the
lock button of your keychain transmitter anytime during the remote start cycle. The shock sensor
will be shunted for the entire run cycle and will resume normal operation after the remote start
unit shuts off.
Check with your installation center to determine if this feature has been programmed into your
system.
OPTIONAL DEVICE OUTPUT ( CHANNEL 3 )
Controlled By: Trunk/Key Button
Other Transmitter button configurations are also available. Consult your installation center for
other configurations not listed above that may have been programmed to operate a specific
feature of your system.
This security system is equipped with an output which will activate when the appropriate trans-
mitter button is depressed for 3 seconds. Although this output is intended to activate the trunk
release option, any other optional devices may be connected to this channel. Consult your
installation center for more information about this output.
ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 )
Controlled By: Option Button
Other Transmitter button configurations are also available. Consult your installation center for
other configurations not listed above that may have been programmed to operate a specific
feature of your system.
This security system has an additional feature that can be connected to a number of different
optional accessories. Some of the more common uses for this channel are;
Remote Window Closure, Remote Garage Door Interface, To remotely operate
the device indicated, momentarily press, or press and hold the appropriate transmitter
button(s) as indicated above.