Laney
3
COMP
3
INPUT
ACTIVE
10
0
GAIN
PASSIVE/
ACTIVE
9
8
7
6
5
4
3
2
1
GAIN
5
5
5
1K
100
BASS
FREQUENCY
2
4
-0+
1
-0+
1
4
3
2
1
2
3
4
PARAMID
500
5
10
5 5
0
VOLUME
TREBLE
8
7
1
6
4
3
2
1
2
3
4
4
3
2
1
-0+
5
4
3
2
1
9
PHONES
D.I.
0
RBW100
POWER
1
RBW100 front
6
1
2
3 4 7 8
9
5 10
Active and Passive/Active Inputs:
Gain:
Compressor:
Bass:
Paramid-Frequency:
Paramid-Gain:
Treble:
Volume:
Direct Inject:
Phones:
FX Loop:
Tuner out:
Horn switch:
ACTIVE and PASSIVE/ACTIVE inputs are provided for
connection of bass guitars. Active basses should be connected via the ACTIVE socket. Non
active basses should be connected using the passive input. Active basses may also be placed in
the PASSIVE input if pre-amp overloading is desired.
This control is used to set the level of gain present in the pre-amp. The higher the level of
gain, the more the signal will clip producing distortion. The GAIN control should be used in
conjunction with the VOLUME control (8) to produce the desired signal characteristics.
Engages and disengages the on-board COMPRESSOR. This compresses the
input-signal giving a punchier sound.
Controls the low-frequency response of the pre-amplifier.
Selects the MID-frequencies to be cut or boosted in conjunction with the
PARAMID GAIN control (6). To access LO mid-frequencies turn the FREQUENCY control
anticlockwise, to access HI mid frequencies turn the FREQUENCY control clockwise.
Sets the level of boost or cut applied to the frequency set by control 5. For
frequency-boost turn the control clockwise. For frequency-cut, turn the control anti-clockwise.
Controls the high-frequency response of the pre-amplifier.
Sets the overall listening level of the amplifier.
XLR socket for direct-injection of the amplifier signal to a mixing-desk or additional
power-amplifier. The XLR socket provides a low-impedance output-signal.
Headphone output for silent practicing.
Send and return sockets are provided for connecting external effects-units.
Socket for connecting external tuner.
Switches the on-board horn either on or off.
6.Paramid Gain:
1.Inputs:
2.Gain:
3.Compressor:
13.Horn switch:
5.Paramid frq:
4.Bass:
7.Treble:
8.Volume:
9.D.I:
CAUTION
ELECRIC SHOCK DO NOT REMOVE
COVERS. NO USER SERVICABLECOVERS. NO USER SERVICABLE
PARTS INSIDE. REFER SERVICINGPA RTSINSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNELTO QUALIFIED SERVICE PERSONNEL
TO REDUCE THE RISK OFTO REDUCE THE RISK OF
FIRE HAZARD REPLACE FUSE WITHFIRE HAZARD REPLACE FUSE WITH
SAME TYPE AND RATING ONLY.SAME TYPE AND RATING ONLY.
REMPLACER LE FUSIBLEREMPLACER LE FUSIBLE
PAR LE MEME ET LE CALIBRE.PARLE MEME ET LE CALIBRE.
MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.MADE IN THE UNITED KINGDOM BY BLT INDUSTRIES LTD.
SUPPLY VOLTAGESUPPLY VOLTAGE
~115V T2A~115V T2A
& FUSE RATING& FUSE RATING
~230V T1A~230V T1A
WARNING
MAXIMUM POWER CONSUMPTIONMAXIMUM POWER CONSUMPTION
140 WATTS ~ 50 - 60 Hz140 WATTS ~ 50 - 60 Hz
CAUTION
ATTENTION
THIS EQUIPMENT MUST BE EARTHED.THIS EQUIPMENT MUST BE EARTHED.
NOT EXPOSE THIS APPLIANCE TONOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.RAIN OR MOISTURE.
WARNING
TO REDUCE THE RISKTO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK DOOF FIRE OR ELECTRIC SHOCK DO
DEBRANCHER A LA PRISEDEBRANCHER A LA PRISE
SERIAL No:
TO REDUCE THE RISK OFTOREDUCE THE RISK OF
ATTENTION
S E C T E U RAVAV TD ' O U VRI R .
CE
SENDSEND
RETURN
EFFECTS LOOPEFFECTS LOOP
RBW100 rearRBW100 rear
13
11
12
10.Phones:
11.FX loop:
12.Tuner out:
