Installation the Microphone Unit
1
Check the installation position of the microphone
(accessory 5).
2
Remove oil and other dirt from the installation
surface.
3
Install the microphone.
4
Wire the cable up to the unit with it secured at
several positions using tape or the like.
Fix a cable with a commercial
item of tape.
Peel off the release coated paper of double-face adhesive
tape to secure the microphone on the place shown above.
Turn the microphone toward the driver.
Accessory 5
85
|
KDC-X996/ KDC-BT952HD
English
|
86
Installation/Removing the Unit Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
! • Cannot set up the subwoofer.
• No output from the subwoofer.
• Cannot set up the subwoofer position of Manual
position setting.
▲
•TheDualzonefunctionisenabled.☞ <Dual Zone
System> (page 48)
•Inthespeakerselectoption,Noneisselectedfor
the subwoofer. ☞ <Speaker Setting> (page 49)
! Cannot set up the rear speaker.
▲
In the speaker select option, None is selected for the
rear speaker. ☞ <Speaker Setting> (page 49)
! Cannot set up the tweeter.
▲
In the speaker select option, None is selected for the
tweeter. ☞ <Speaker Setting> (page 49)
! • Cannot set up the equalizer.
• Cannot set up the Bass Boost.
• Cannot set up the Sound Enhancements.
• Cannot set up the Position control.
▲
•TheDualzonefunctionisenabled.☞ <Dual Zone
System> (page 48)
•TheDSPfunctionisdisabled.☞ “DSP Set” of <Audio
Control> (page 45)
•Inthespeakerselectoption,Noneisselectedfor
the rear speakers. ☞ <Speaker Setting> (page 49)
! • Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
▲
The Dual zone function is disabled. ☞ <Dual Zone
System> (page 48)
! Cannot set up Display.
▲
<Demonstration mode Setting> (page 43) is not
turned off.
! The number of songs contained in “Songs”
category of this unit is different from that
contained in “Songs” category of iPod.
▲
Podcast files are not counted in this unit as this unit
does not support the playback of podcast files.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
General
? The operation check sound (beep sound) does not
sound.
✔ The preout jack is being used.
☞ The Touch Sensor Tone cannot be output from
the preout jack.
? The illumination flashes when the knob or button
is operated.
✔ This is the key illumination effect.
☞ You set this effect in “ILLUMI Effect” of <Display
Setting> (page 35).
? The key illumination effect brought about in
conjunction with the sound volume is small.
✔ The key illumination effect may be insufficient
depending on the sound volume and sound quality.
Tuner source
? Radio reception is poor.
✔ The car antenna is not extended.
☞ Pull the antenna out all the way.
✔ Antenna Control wire is not connected.
☞ Connect the ANT.CONT wire.
Disc source
? The specified disc does not play, but another one
plays instead.
✔ The specified CD is quite dirty.
☞ Clean the CD, referring to the CD cleaning of the
section on <Handling CDs> (page 6).
✔ The disc is loaded in a different slot from that
specified.
☞ Eject the disc magazine and check the number
for the specified disc.
✔ The disc is severely scratched.
☞ Try another disc instead.
Audio file source
? The sound skips when an Audio file is being
played.
✔ The media is scratched or dirty.
☞ Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 6).
✔ The recording condition is bad.
☞ Record the media again or use another media.
Hands-free
? The hands-free talk volume is low.
✔ The hands-free talk volume is set at a low level.
☞ The hands-free talk volume can be adjusted
independently. Adjust it during hands-free talk.
“Mic Gain” and “NR Level” <Bluetooth Setting>
(page 55).
? No sound is heard from the rear speakers.
✔ You are talking in the hand-free talk mode.
☞ No sound is heard from the rear speakers in the
hands-free talk mode.
? No beep is heard at reception of an incoming call.
✔ No beep is heard depending on the type of your
cell-phone.
☞ The “Call Beep” of <Bluetooth Setting> (page
55) is set ON.
