Filter
Top Products
OPERATION
Alert Priority
When two or more signals are received at the
same time, the alert priority is:
1. Laser 2. Speed Radar 3. Safety Radar
Example: If X band is alerting, then suddenly a
laser signal is detected, the laser warning will
override the X band alert.
Compass Calibration Set-up
The unit will need to be calibrated in order for
the compass to provide accurate readings. To
calibrate the unit, perform the following proce-
dure:
1
1
.
.
Mount the unit level in the center of the
vehicle’
s windshield. Make sure there are no
other magnetic sources near the detector
(i.e., speaker).
2
2
. Select a large clear area (parking lot or field)
without any power lines.
3
3
. Press the Menu button until display shows
C
C
A
A
L
L
M
M
O
O
D
D
E
E
. Then press the Dark and Quiet buttons
simultaneously
. The display shows (scrolling):
4
4
. If calibration does not automatically finish press
the Dark and Quiet buttons simultaneously to com-
plete calibration. The unit will beep twice and dis-
play shows, for example:
Note: In Combo Mode an “
H
H
” or “
C
C
” will be
shown to indicate mode of operation.
Important: If unit mounting is relocated in the
vehicle, (i.e., visor to windshield mounting or
dash mounting), or if the unit is moved to
another vehicle, you must recalibrate the com-
pass.
OPERATION
Reset Features
All user features can be reset to factory settings.
•Unplug the Power Cord from the unit.
•Press and hold the Power and Quiet buttons.
•Plug the Power Cord into the unit.
•Wait for 2 beeps.
•Release the Power and Quiet buttons.
Unit is now reset to the following features
and settings.
Default factory settings ar
e:
1. S1: (For Intellicord
®
) Power ON or OFF.
2. S2: (For Intellicord
®
) Quiet feature.
3. Combo Mode.
4. HIGHWAY Mode.
5. Dim/Dark Mode to full illumination of display.
6. Auto Quiet Mode OFF.
7. Safety Radar OFF.
8. Vehicle Battery Saver ON/3hrs.
9. Full Power Up sequence.
10. Default TONE 3.
11. All Bands ON.
12. Laser ON.
13. POP ON.
14. Voice ON.
15. LED Periscope to BLNK.
Intellicord
®
Ready
Using Whistler’s optional Intellicord
®
Power Cable
allows some models to control the detector’s fea-
tures such as Power On/Off, City Modes,
Dim/Dark, and Quiet/Auto Quiet with a simple
press of the button on the Power Cable. Two fea-
tures can be controlled: one by a short press of
the button, and the second by a long press of the
button. Option Mode allows the user to program
the feature assignments.
OPERATION
(
(
X
X
T
T
R
R
-
-
6
6
9
9
5
5
o
o
n
n
l
l
y
y
)
)
Whistler has two new exciting fea-
tur
es that will assist the driving enthusiast to further
identify threats from laser and Ka band radar guns.
Ka RSID (Ka Radar Signal IDentifier)
Identify the difference between the likelihood of a
Ka threat vs. the likelihood of a Ka false from anoth-
er source (possible radar detector). The Ka RSID
feature will educate you to the common Ka speed
radar by displaying the nominal police radar fre-
quencies of 33.8GHz / 34.0GHz / 34.3GHz / 34.7GHz
/ 35.5GHz. The Ka alerts that do not fall into the com-
mon Ka speed radar windows will be reported only as
Ka.
Note: This product is not a frequency counter. Your
XTR-695 will categorize the received Ka signal and
select the appropriate information. Treat every Ka
alert with caution.
LSID (Laser Signal IDentifier)
Identify the Laser gun’s pulse rate or PPS (Pulses Per
Second) that is transmitted by the speed laser gun.
LSID may also be used to identify other forms of
laser sources such as LACC (Laser Assisted Cruise
Control) systems found in some high end vehicles.
If the Laser PPS information displayed is due to
another source such as local airports or LACC, LSID
allows you to Lock Out this rate from giving you the
continuous audio alert during this and any new
encounter of the same rate. To Lock Out a PPS, sim-
ply press the Quiet button during the Laser alert.
This will place an * on the screen beside the PPS
rate and Lock Out this signature ID. Any new
encounter with the same Laser Signature ID will pro-
vide the display information and two quick beeps.
Note: Common Laser PPS rates used in the USA
are 100 / 125 / 130 / 200 / 238 / 380Hz. Others Laser
PPS rates used outside the USA include 600Hz.
Caution: Do not lock out a PPS rate if is is close to
known speed laser guns.
14 15
16