Filter
Top Products
OPERATION
Quiet Mode
Quiet cancels audio during an alert and any new
a
lert within 20 seconds. After 20 seconds,
a
pproximately 2 beeps are provided on any new
alert and unit then remains quiet.
• Press Quiet to cancel the audio.
• To restore the standard audio alert pattern, press Quiet
a second time during an alert or tun the unit off, then on.
Teach/Tutorial Mode
P
rovides simulated alerts for each type of signal.
• Press City and Quiet/VOL simultaneously and release.
• Display Shows:
• Press Power/BL to exit.
City/City 1/City 2 Mode
Whistler’s Three Stage City Mode is designed to
reduce the annoyance of automatic door
openers, intrusion alarms and other devices which
share frequencies with police radar. Generally, X
band is used for these devices.
• Press City button to cancel Highway Mode
and engage City Mode.
• Press City button again to enter City 1 Mode
• Press City button again to enter City 2 Mode
• Press City button a fourth time to cancel City 2
Mode and return the unit to Highway Mode.
In City Mode, weak speed/safety radar signals
give an initial alarm of two beeps, and then
remains quiet unless the signal becomes very
strong. When the signal strength increases, two
additional beeps are provided. City 1 and City 2
Modes operate the same as Highway Mode, but
in City 1 Mode, X band requires a stronger
signal to alert. In City 2 Mode, X-band is not
detected.
Caution: Some towns/small cities may still be
using X band radar. City Modes do not change
the audio aler
t for laser or VG-2.
OPERATION
Highway Mode
Highway mode provides full audio warnings any
t
ime radar (X, K, Ka, Safety Radar) or laser signals
are detected, and is recommended for open road
driving.
For more information on City and Highway modes, please visit
our FAQ page on our website: www
.whistlergroup.com
Backlight Setting
The backlighting can be programmed to be
i
lluminated all the time, only when alarming or
choices in between. The options are selectable by
p
ressing and holding the Power/BL button on the
unit. The options are:
O
O
F
F
F
F
-
-
O
O
F
F
F
F
= Backlight is off during normal operation and
off when the unit alarms
O
O
F
F
F
F
-
-
D
D
I
I
M
M
= Backlight is off during normal operation and
dim when the unit alarms.
O
O
F
F
F
F
-
-
B
B
R
R
T
T
= Backlight is off during normal operation and
bright when the unit alarms.
D
D
I
I
M
M
-
-
O
O
F
F
F
F
= Backlight is dim during normal operation and
o
ff when the unit alarms.
D
D
I
I
M
M
-
-
D
D
I
I
M
M
=
Backlight is dim during normal operation and
dim when the unit alarms.
D
D
I
I
M
M
-
-
B
B
R
R
T
T
= Backlight is dim during normal operation and
bright when the unit alarms.
B
B
R
R
T
T
-
-
B
B
R
R
T
T
= Backlight is bright during normal operation and
bright when the unit alarms.
Backlight will turn on, if selected, while the unit
alarms and remain on for 3 seconds after the unit
stops alarming. When any button is pressed, the
backlight will illuminate at the dim setting and
remain on for 3 seconds afterwards. The backlight
will also illuminate while in option mode.
Low Profile Alert Periscopes
Whistler’s Low Profile Alert Periscopes provide an
added attention getting visual alert. The two extra
LED’
s flash on and of
f when the unit alarms to
provide a unique visual alert. This alert can be
programmed through the Option Select Mode to
be: ON, OFF, or FLASHING during alerts.
OPERATION
8910
Compass Calibration (XTR-540 only)
T
he unit needs to be calibrated in order for the
compass to provide accurate headings. To calibrate
the unit, perform the following procedure:
1
1
.
.
M
ount the unit level in the center of the
v
ehicle’s windshield. Make sure there are no
m
agnetic sour
ces near the detector (
i.e., speaker)
.
2
2
.
Select a large, clear area
(
parking lot or field)
without any power lines.
3
3
. P
r
e
ss the Menu button until display
shows
C
C
A
A
L
L
M
M
O
O
D
D
E
E
. Then press the Power/BL and Quiet/Vol
buttons simultaneously. The display shows (scrolling):
4
4
. If calibration does not automatically finish, press the
Power/BL and Quiet/VOL b
uttons simultaneously to
complete calibration. T
he unit will beep twice and
display:
Important: If the unit mounting is relocated in the
v
ehicle, (i.e., visor to windshield mounting or dash
m
ounting), or if the unit is moved to another vehicle,
you must recalibrate the compass.
VG-2 Mode
See Option Select Mode to turn this feature
on/off. When a VG-2 signal is detected, the VG-2
alert is sounded and the display flashes “VG-2”.
After 3 seconds, the audio is canceled and the
display no longer flashes. This cycle is repeated
if the VG-2 signal is detected again.
D
D
u
u
r
r
i
i
n
n
g
g
t
t
h
h
e
e
p
p
e
e
r
r
i
i
o
o
d
d
a
a
V
V
G
G
-
-
2
2
s
s
i
i
g
g
n
n
a
a
l
l
i
i
s
s
d
d
e
e
t
t
e
e
c
c
t
t
e
e
d
d
,
,
a
a
r
r
a
a
d
d
a
a
r
r
s
s
i
i
g
g
n
n
a
a
l
l
c
c
a
a
n
n
n
n
o
o
t
t
b
b
e
e
d
d
e
e
t
t
e
e
c
c
t
t
e
e
d
d
.
.
However,
because the VG-2 alert has confirmed that a
patrol car is nearby, you are already aware of the
potential for speed monitoring
and can adjust
your speed accordingly. Laser detection is not
affected while a VG-2 signal is detected. (See
page 18 for more information)