Filter
Top Products
POP™ MODE ALERTS
LASER/RADAR ALERTS
Safety Warning System/Audio/Visual
Alerts When your Whistler detector detects a
safety radar signal, it provides a distinctive audio
tone and the Numeric Icon display shows an
“S.” and a decimal point when a Safety radar sig-
nal is detected. (XTR-255/260/330)
N
N
o
o
t
t
e
e
:
:
You will not be able to receive SWS alerts if
transmitters are not located in your area.
VG-2 ALERTS
VG-2 Detection Mode
The VG-2, also known as a “radar detector
detector,” is a special receiver used by police to
detect signals radiated by a radar detector. See
page 21 for more information on VG-2.
When a VG-2 signal is detected, the VG-2 alert
is sounded. After 3 seconds, the audio is can-
celled and the VG-2 indicator flashes at a slower
rate. Every 30 seconds, the detector checks for a
VG-2 signal. This cycle is repeated if the VG-2
signal is detected again. If no signal is detected,
two beeps are provided indicating an “all clear”
condition.
During the period a VG-2 signal is detected, a
radar signal cannot be detected. However,
because the VG-2 alert has confirmed that a
patrol car is nearby, you are already aware of the
potential for speed monitoring and can adjust
your speed accordingly. Laser detection is not
affected while a VG-2 signal is detected.
14 15
TROUBLESHOOTING GUIDE
Reset Features
All user features can be reset to factory settings.
Default Factory
1. Unplug Power Cord from unit.
2. Press and hold Quiet.
3. Plug the Power Cord into the unit.
(Power switch turned on)
4. Wait for 2 beeps.
5. Release the Quiet button.
Unit is now reset.
Default Factory Settings are:
• Highway Mode.
• Dim/Dark Mode to full illumination of display.
• Auto Quiet Mode OFF.
• VG-2 Detection Mode OFF.
• Self Test Mute OFF
• D.A.D. ON (XTR-255/260)
• Dual LED Alert Periscope to Flash
• POP™ Mode ON (XTR-330)
Your Whistler detector is expertly
engineered and designed to exacting
quality standards to provide you with
reliable, trouble-free operation. If your unit
has been correctly installed following the
guidelines in this manual, but is not
operating optimally, please refer to the
troubleshooting guide below.
PROBLEM: No display or audio.
Check fuse in plug; replace if necessary with a
2 amp 3AG type. Check fuse for lighter sock-
et; replace if necessary. Make sure cigarette
the lighter socket is clean.
PROBLEM: Audio alerts are not loud
enough.
Cancel Auto Quiet Mode or City
Mode. Check audio level setting
(see pg.8).
X
X
T
T
R
R
-
-
2
2
6
6
0
0
/
/
3
3
3
3
0
0
S
S
W
W
S
S
D
D
i
i
s
s
p
p
l
l
a
a
y
y
Alert
16
POP
™
Mode Alerts
Because POP
™
Mode radar utilizes the same
K or Ka band frequencies, POP
™
Mode Alerts will be
displayed as regular radar alerts.
OPTION SELECT MODE
Option Select Mode (XTR-140)
To turn VG-2 ON/OFF, press the Menu button and the
“V” icon will illuminate indicating VG-2 is engaged.
Press the Menu button again to disengage VG-2.
Option Select Mode (XTR-255/260/330)
Press the Menu button to enter Option Select
Mode. Each press of the Menu button changes
to the next selectable feature.
The Dark (
D
D
) button and the Quiet (
Q
Q
) button
turns the feature ON/OFF or Blinking. The deci-
mal point illumination indicates whether a fea-
ture is on or off. A button must be pressed with-
in 20 seconds or Option Select Mode will auto-
matically be exited.
Model: XTR-255/260
Feature: Option:
VG-2 (default = OFF)
DD
for ON,
QQ
for OFF
Dual LED Alert Periscope
DD
or
QQ
for ON, OFF, BLINKING
(default = Blinking with aler
t)
Dual Alert Display
DD
or
QQ
for ON, OFF, BLINKING
(default = Blinking with alert)
Model: XTR-330
Feature: Option:
VG-2 (default = OFF)
DD
for ON,
QQ
for OFF
Dual LED Alert Periscope
DD
or
QQ
for ON, OFF, BLINKING
(default = Blinking with alert)
POP
™
Mode
DD
for ON,
QQ
for OFF
(default = ON)
SWS
DD
for ON,
QQ
for OFF
(default = ON)