Filter
Top Products
Windshield Mounting
• Install the two suction cups and rubber bumper
onto the bracket by fitting them into their holes.
• Press the suction cups onto the windshield at the
location you have chosen.
• Slide the detector onto the bracket until it locks
into place.
• If necessary, the unit may be leveled by bending
the windshield bracket.
• Press the bracket release button and remove the
detector before bending.
Power Cord Connection
• Plug the small end of the power cord into the
unit’s power jack.
• Plug the large end into the vehicle’s cigarette
lighter socket.
N
N
o
o
t
t
e
e
:
:
Cord fits tightly into detector. When installing
the cord, expect some resistance.
Fuse Replacement
The lighter socket plug is equipped with a
replaceable 2 amp 3AG fuse located behind the
silver tip. To replace the fuse, carefully unscrew
the tip of the plug.
I
I
m
m
p
p
o
o
r
r
t
t
a
a
n
n
t
t
:
:
Unscrew slowly. The tip contains a spring
which may fly out when disassembling. Insert the new fuse
with the spring and screw on the tip. With use, screw cap
on plug may loosen. Retighten occasionally.
Unscrew the tip of the lighter socket plug
carefully when replacing the 2 amp fuse.
INSTALLATION
Battery Life
The unit can provide approximately 15 hours of
laser/radar detection. There are settings that can
maximize battery life.
1) Display intensity set to Dim
2) Auto Quiet engaged
3) Auto Shut Off set to 1 hour
4) Using a lower volume setting
5) Using Mute whenever possible
Important: The detector’
s display will flash a “
I
I
”
and three fast beeps will sound when the batter-
ies have approximately one hour of battery life
left. This is a reminder to recharge your batter-
ies.
Battery Charging
P
P
o
o
w
w
e
e
r
r
C
C
o
o
r
r
d
d
: Plug your included power cord into
your detector and into your lighter socket to
slowly char
ge the rechargeable batteries. This
will also provide power to the detector. The dis-
play will dimly blink the “
I
I
I
I
I
I
” icon when the unit
is charging the batteries. When the power cable
is removed from the detector or the vehicle’s
lighter socket is switched off, the unit will alarm
and illuminate the icons in a sequencing fashion,
then turn of
f.
N
N
o
o
t
t
e
e
:
:
As with all battery operated devices, remove
the batteries when this unit will not be used for an
extended period of time. Damage caused by leaky
or improperly charged batteries are not covered
under warranty
.
S
S
o
o
l
l
a
a
r
r
P
P
a
a
n
n
e
e
l
l
: In direct sunlight, the solar panel
provides an additional charge to the batteries.
The solar panel is not functional when the unit is
power
ed by the power cord.
OPERATION
Windshield
Mounting
56
Rubber Bumper
Power On and Self-Test
Each time your Whistler detector is turned on,
an automatic self-test sequence confirms that
the speaker and visual displays are functional.
• Press Power. Display shows in order:
1. X-Band 2. K-Band 3. Ka-Band 4. LASER
5. SWS 6. Battery Status
7
7
.
.
Highway
Self Test Mute
Simply press the Quiet button during the
self-test sequence to cancel the self-test audio. This
will not affect radar/laser alerts. To restore the
self-test audio, simply press the Quiet button during
the next self-test.
Setting Saver
Setting Saver saves your personalized settings
when the detector is turned off or you lose power.
Feature Engaged Confirmation
Each time a button is pressed, one beep confirms
feature “on”, two beeps confirm feature “off”.
Audio Level Adjustment
The audio levels can be adjusted high to low or
low to high.
• Press and hold the “VOL” button and the
volume level will increase (Level “
I
I
I
I
I
I
”) then
proceed to lower the volume (Level 0).
Continuing to hold this button will repeat the
sequence. As audio level is adjusted, beeps are
provided and the display indicates volume level.
OPERATION
7