Filter
Top Products
OPERATION
8
Auto Quiet Mode
Auto Quiet reduces the selected audio level to
l
evel (1) approximately 5 seconds after a radar or
safety radar signal is detected. The alert for any
new signal within 20 seconds will resume at level
(
1). Auto Quiet does not affect laser alerts.
• Press Quiet button (before a signal is detected) to
engage Auto Quiet.
• Once the Auto Quiet mode is engaged, you
may cancel the audio alarm by pressing Quiet.
• Press Quiet (when the unit is not alarming) to
cancel Auto Quiet mode.
Stay Alert Feature
The Stay Alert Feature is designed to test a
driver’s alertness. To engage (when unit is not
alarming) :
• Press and hold City for approximately 2 seconds.
Release button during or immediately after the alert is
given.
The “H” or “C” will flash indicating Stay Alert is
activated. Within 30-60 seconds two beeps are
sounded; to show alertness, the driver must press
either the Menu, City, or Quiet button within 3-5
seconds.
If the button is pressed within 3-5 seconds, the cycle is
repeated. If a button is not pressed with in 3-5 seconds,
the alarm sounds and the entire display will flash.
• Press Power to exit
WARNING!!! Stay Alert is NOT intended as a
substitute for adequate rest. You should NOT
operate a vehicle if you are drowsy. During
extended periods of vehicle operation,
you should
take frequent breaks. Improper reliance on the Stay
Alert feature may result in vehicle damage,
personal injury or death.
NEVER OPERATE A
VEHICLE IF YOU ARE DROWSY
.
Low Profile Alert Periscopes
Whistler’s Low Profile Alert Periscopes provide an
a
dded attention getting visual alert. The two extra
L
ED’s flash on and off when the unit alarms to
provide a unique visual alert. This alert can be
programmed through the Option Select Mode to
be: ON, OFF,
or FLASHING during alerts.
City/City 1/City 2 Modes
W
histler’s Three Stage City Mode is designed to
reduce the annoyance of automatic door
openers, intru
sion alarms and other devices
which share frequencies with police radar.
Generally, X band is used for these devices.
• Press City to cancel Highway Mode and
engage City Mode.
• Press City button again to enter City 1 Mode
• Press City button again to enter City 2 Mode
• Press City a fourth time to cancel City 2 Mode
and return the unit to Highway Mode.
In City Mode, weak speed/safety radar signals
give an initial alarm of two beeps, and then
remains quiet unless the signal becomes very
strong. When the signal strength increases, two
additional beeps are provided. City 1 and City 2
Modes operate the same as Highway Mode, but
in City 1 Mode, X band requires a stronger
signal to alert. In City 2 Mode, X-band is not
detected.
Caution: Some towns/small cities may still be
using X band radar. City Modes do not change
the audio alert for laser.
OPERATION
9
Highway Mode
Highway mode provides full audio warnings any
t
ime radar (X, K, Ka, Safety Radar) or laser
signals are detected, and is recommended for
open road driving.
For more
information on City and Highway
m
ode, please visit our FAQ page on our
website:
www.whistlergroup.com
Teach/Tutorial Mode
Provides simulated alerts for each type of signal.
• Press City and Quiet buttons simultaneously
and release.
• Press Power to exit.
Dim/Dark Modes
Dim/Dark Mode reduces the illumination of the
display
• Press and release the Dark button to reduce
illumination to a dim setting.
• Press and release the Dark button a second
time to engage Dark Mode. The display
illumination is further reduced.
Dim or Dark can be engaged during an alert. In
Dark Mode, the display goes dark for as long as
a signal is being detected and 20 seconds after,
then the display returns to the dimmer setting.
• Press and release the Dark button a third time
to restore the display to full illumination.
OPERATION
10