Metra Electronics 70-6522 Automobile Accessories User Manual


  Open as PDF
of 2
 
2007 AND UP
CHRYSLER/DODGE/JEEP VEHICLES
Rev. 04-10-09
2007 AND UP
CHRYSLER/DODGE/JEEP VEHICLES
Rev. 04-10-09
2007 AND UP
CHRYSLER/DODGE/JEEP VEHICLES
Rev. 04-10-09
2007 AND UP
CHRYSLER/DODGE/JEEP VEHICLES
Rev. 04-10-09
Due to the fact that a switched 12-volt
accessory
lead does NOT exist in the
factory
harness, an accessory source
must
be located.
1. Using the separate red wire provided with
the fuse tap, locate an accessory power
source in the vehicle’s fuse box.
2. Connect this red wire to the aftermarket
head unit switched accessory lead.
3. Use Metra’s standard wiring instructions
for the remainder of the installation.
Due to the fact that a switched 12-volt
accessory
lead does NOT exist in the
factory
harness, an accessory source
must
be located.
1. Using the separate red wire provided with
the fuse tap, locate an accessory power
source in the vehicle’s fuse box.
2. Connect this red wire to the aftermarket
head unit switched accessory lead.
3. Use Metra’s standard wiring instructions
for the remainder of the installation.
Due to the fact that a switched 12-volt
accessory
lead does NOT exist in the
factory
harness, an accessory source
must
be located.
1. Using the separate red wire provided with
the
fuse tap, locate an accessory power
source
in the vehicle’s fuse box.
2. Connect this red wire to the aftermarket
head
unit switched accessory lead.
3. Use Metra’s standard wiring instructions
for
the remainder of the installation.
Due to the fact that a switched 12-volt
accessory
lead does NOT exist in the
factory
harness, an accessory source
must
be located.
1. Using the separate red wire provided with
the
fuse tap, locate an accessory power
source
in the vehicle’s fuse box.
2. Connect this red wire to the aftermarket
head
unit switched accessory lead.
3. Use Metra’s standard wiring instructions
for
the remainder of the installation.
2007 AND UP
CHRYSLER/DODGE/JEEP VEHICLES
Rev. 04-10-09
2007 AND UP
CHRYSLER/DODGE/JEEP VEHICLES
Rev. 04-10-09
2007 AND UP
CHRYSLER/DODGE/JEEP VEHICLES
Rev. 04-10-09
2007 AND UP
CHRYSLER/DODGE/JEEP VEHICLES
Rev. 04-10-09
Due to the fact that a switched 12-volt
accessory
lead does NOT exist in the
factory
harness, an accessory source
must
be located.
1. Using the separate red wire provided with
the fuse tap, locate an accessory power
source in the vehicle’s fuse box.
2. Connect this red wire to the aftermarket
head unit switched accessory lead.
3. Use Metra’s standard wiring instructions
for the remainder of the installation.
Due to the fact that a switched 12-volt
accessory
lead does NOT exist in the
factory
harness, an accessory source
must
be located.
1. Using the separate red wire provided with
the fuse tap, locate an accessory power
source in the vehicle’s fuse box.
2. Connect this red wire to the aftermarket
head unit switched accessory lead.
3. Use Metra’s standard wiring instructions
for the remainder of the installation.
Due to the fact that a switched 12-volt
accessory
lead does NOT exist in the
factory
harness, an accessory source
must
be located.
1. Using the separate red wire provided with
the
fuse tap, locate an accessory power
source
in the vehicle’s fuse box.
2. Connect this red wire to the aftermarket
head
unit switched accessory lead.
3. Use Metra’s standard wiring instructions
for
the remainder of the installation.
Due to the fact that a switched 12-volt
accessory
lead does NOT exist in the
factory
harness, an accessory source
must
be located.
1. Using the separate red wire provided with
the
fuse tap, locate an accessory power
source
in the vehicle’s fuse box.
2. Connect this red wire to the aftermarket
head
unit switched accessory lead.
3. Use Metra’s standard wiring instructions
for
the remainder of the installation.
 previous