Filter
Top Products
Transmitter Button
System Function
Locks the Vehicle's Doors and
Cargo Door
Unlocks the Vehicle's Doors
Locks the Cargo Door
Unlocks the Cargo Door
Turns the Porch Light "ON" or "OFF"
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
Operation
A. 4-Button Transmitter Operation
+
Transmitter Button
System Function
Locks the Vehicle's Doors and
Cargo Door
Unlocks the Vehicle's Doors
Unlocks the Cargo Doors
(Can be reprogrammed to Turn the Porch Light
"ON" or "OFF")
Turns the Porch Light "ON" or "OFF"
(Can be programmed to Unlock the Cargo Doors)
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
Upon Vehicle's Door Unlock
B. 3-Button Transmitter Operation
© Copyright 2005 Magnadyne Corporation
MKE-34A-UM Rev. A 6-27-05
+
System Function
Locks the Vehicle's Doors and
Cargo Door(s)
Unlocks the Vehicle's Doors
Locks or Unlocks the Cargo Door
(Operation is Sequential)
Turns On the Porch Light or Turns Off
the Porch Light (Operation is Sequential)
Activates the Channel 3 Output
Activates the Channel 4 Output
Activates the Channel 5 Output
Turns "ON" or "OFF" the Button Beep
Feature of the Keypad
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light T
urns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
C. Keypad Operation
Keypad
Press the "LOCK" Key
Key in the "User Code"
Press and Hold the
"1/2" Key for 3 Seconds
Press and Hold the
"3/4" Key for 3 Seconds
Key in the "User Code",
then Press and Hold
the "5/6" Key for 5
Seconds
Key in the "User Code",
then Press and Hold
the "7/8" Key for 5
Seconds
Key in the "User Code",
then Press and Hold
the "9/0" Key for 5
Seconds
Key in the "User Code",
then Press and Hold
the "LOCK" Key for 3
Seconds
C. Programming the User Code
(The default user code is "54321")
Note: This mode will only retain the last 4 "user
codes" programmed. If the user code memory is
exceeded, the security system will start deleting
user codes from memory in chronological order.
1. Enter the program code "12345" on the keypad.
The beeper will emit a long chirp to confirm the
correct code was entered.
2. Enter a new 4 to 6 digit user code on the keypad.
Do not use "1234".
3. Finish by pressing the "LOCK" key on the key-
pad. 1 long beep with 2 short beeps will confirm
the new user code has been stored into memory.
4. If you have additional user codes (up to 4) that
need to be programmed, repeat steps 2-3 for
each new user code.
Exit: Press and hold the "LOCK" key for 1 second or
if 15 seconds of inactivity occurs during the above
steps, the unit will revert back to the last success-
fully stored code. 3 longs beeps confirm exit.
D. Programming the Keypad Button Chirp On / Off.
1. Enter the user code.
2. Within 5 seconds, press and hold the LOCK
button for 3 seconds.
1 Beep from the keypad = Keypad Chirp "ON"
3 Beeps from the keypad = Keypad Chirp "OFF"
1 Beep = Keypad Chirp is "ON" (Default)
3 Beeps = Keypad Chirp is "OFF"
Programming (Continued)
Operation (Continued)
MKE-34-UM.qxp 6/27/05 2:23 PM Page 2