Filter
Top Products
BACKLIGHT AND PROJECTION INTENSITY: Press and release the
SNOOZE/LIGHT button to adjust the brightness of the backlight and
projection (together):
ON High intensity: The backlight and projection are defaulted to HI when
the Adapter is in use.
ON Low intensity: Press and release SNOOZE/LIGHT button once
OFF: Press and release SNOOZE/LIGHT button
ON High intensity (default): Press and release SNOOZE/LIGHT button
Note: When the Adapter is NOT in use, the High/Low/On/Off features are
not available.
PROJECTION:
Battery Power: Press and release the SNOOZE/LIGHT button to show the
projection for 10 seconds.
Note: Projection will not display constantly when operating on battery power.
A/C Power: Projection is displayed constantly unless turned off.
Note: can be turned off see “Backlight and Projection Intensity”
Rotate Projection: Press and release the PROJECTION button to rotate
projection image 90 degrees. Press and release the PROJECTION button
again to rotate another 90 degrees.
Change Projection Mode: Hold, then release the PROJECTION button to
switch projection modes. Watch the projection image to view the changes.
o Time and Outdoor Temperature: alternate every 5 seconds (default)
o Time: Hold and release PROJECTION button
o Outdoor Temperature: Hold and release PROJECT button again
TEMPERATURE TREND ICONS:
The indoor and outdoor temperature trend indicators are updated every 30
minutes. These trends represent temperature changes over the past three
hours.
Temperature rising more than 2°F /1°C in the past three hours
Temperature has not changed more than 2°F /1°C in the past
three hours
Temperature falling more than 2°F /1°C in the past three hours
The temperature trend indicators are shown next to the indoor temperature
and outdoor temperature readings.
POSITIONING OUTDOOR TRANSMITTER:
Once the Projection Alarm shows the outdoor temperature, place it and the
transmitter in the desired locations and wait approximately 1-hour before
permanently mounting the transmitter to ensure that there is proper
reception. The transmitter should be mounted vertically, in a shaded,
protected area, at least 6 feet from the ground to avoid damage and ensure
accurate readings. The transmitter is water resistant, not waterproof and
should not be placed anywhere it will become submerged in water or subject
to standing water or snow.
WALL MOUNT
Choose a shaded location (under an overhang) for the
transmitter that is within the confirmed wireless reception
range of the Projection Alarm for accuracy.
Install one mounting screw (not included) into a wall leaving
approximately ½ of an inch (12.7mm) extended.
Place the hanging hole (on the back of the transmitter) onto
the mounting screw and gently slide the transmitter down
onto the mounting screw to secure it into place.
IMPORTANT: For true temperature readings, mount the transmitter out of
direct sunlight on a North-facing wall or in any other well shaded area like
under an eave or deck rail. The maximum transmitting range in open air is
over 200-feet (60 meters). Obstacles such as walls, windows, stucco,
concrete, and large metal objects can reduce the range. Place the transmitter
at least 6 feet in the air to improve signal transmission.
LOW BATTERY:
When this icon appears in the indoor (IN) reading section, replace the
batteries in the Projection Alarm.
When this icon appears in the outdoor (OUT) readings section, replace
the batteries in the outdoor transmitter.
CARE AND MAINTENANCE:
Do Not Mix Old and New Batteries
Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries
Do not expose the Projection Alarm to extreme temperatures, vibration or
shock.
Keep the Projection Alarm dry.
Clean the Projection Alarm with a soft damp cloth. Do not use solvents or
scouring agents.
The Projection Alarm is not a toy. Keep it out of reach of children.
The Projection Alarm is not to be used for medical purpose or for public
information, but is determined for home use only.
The specifications of this Projection Alarm may change without prior notice.
Improper use or unauthorized opening of housing will void the warranty.
If the Projection Alarm does not work properly, change the batteries and/or
check the a/c cord connection.
SPECIFICATIONS:
Indoor:
Temperature Range: +32°F to +122°F (0°C to 50°C)
Accuracy: +/- 2 degrees Fahrenheit
Interval: About every 30 seconds
Outdoor:
Temperature Range: -40°F to 140°F (-40°C to 60°C)
Alkaline Batteries: -20°F to 140°F (-28.8°C to 60°C)
Lithium Batteries: -40°F to 140°F (-40°C to 60°C)
Temperatures below - 20°F (-28.8°C) require
Lithium batteries in the outdoor transmitter.
Distance: Over 200 ft. (60 meters) RF 433MHz (open air)
Interval: About every 30 seconds
Power:
Projection Alarm: 5-volt a/c power adapter (included)
Optional 2-AAA, IEC, LR3 batteries (not included)
TX14 Transmitter: 2-AA, IEC, LR6 batteries (not included)
Battery Life:
TX14 Transmitter
Battery Life:
Battery life is over 24 months when using reputable
battery brands for both Alkaline and Lithium battery
Projection Alarm
Battery Backup:
Battery life is over 24 months when using the AC
adapter for primary power
Dimensions:
Projection Alarm: 5.23” L x 1.96” W x 4.33” H (133 x 50 x 110 mm)
TX14 Transmitter: 2.5” L x 1.42” W x 3.98” H (64 x 36 x 101 mm)
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product
against manufacturing defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on
products purchased and used in North America and only to the original purchaser of
this product. To receive warranty service, the purchaser must contact La Crosse
Technology, Ltd for problem determination and service procedures. Warranty
service can only be performed by a La Crosse Technology, Ltd authorized service
center. The original dated bill of sale must be presented upon request as proof of
purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized
service center.
La Crosse Technology, Ltd will repair or replace this product, at our option and at no
charge as stipulated herein, with new or reconditioned parts or products if found to
be defective during the limited warranty period specified above. All replaced parts
and products become the property of La Crosse Technology, Ltd and must be
returned to La Crosse Technology, Ltd. Replacement parts and products assume
the remaining original warranty, or ninety (90) days, whichever is longer. La Crosse
Technology, Ltd will pay all expenses for labor and materials for all repairs covered
by this warranty. If necessary repairs are not covered by this warranty, or if a
product is examined which is not in need or repair, you will be charged for the
repairs or examination. The owner must pay any shipping charges incurred in
getting the La Crosse Technology, Ltd product to a La Crosse Technology, Ltd
authorized service center. La Crosse Technology, Ltd will pay ground return
shipping charges to the owner of the product to a USA address only.
The La Crosse Technology, Ltd warranty covers all defects in material and
workmanship with the following specified exceptions: (1) damage caused by
accident, unreasonable use or neglect (including the lack of reasonable and
necessary maintenance); (2) damage occurring during shipment (claims must be
presented to the carrier); (3) damage to, or deterioration of, any accessory or
decorative surface; (4) damage resulting from failure to follow instructions contained
in the owner’s manual; (5) damage resulting from the performance of repairs or
alterations by someone other than an authorized La Crosse Technology, Ltd
authorized service center; (6) units used for other than home use (7) applications
and uses that this product was not intended or (8) the products inability to receive a
signal due to any source of interference.. This warranty covers only actual defects
within the product itself, and does not cover the cost of installation or removal from
a fixed installation, normal set-up or adjustments, claims based on
misrepresentation by the seller or performance variations resulting from installation-
related circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES
ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT.
THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR
PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF
CHILDREN’S REACH.
This warranty gives you specific legal rights. You may also have other rights
specific to the State. Some States do not allow the exclusion of consequential or
incidental damages therefore the above exclusion of limitation may not apply to you.
For warranty work, technical support, or information contact:
La Crosse Technology, Ltd
2817 Losey Blvd. S.
La Crosse, WI 54601
The complete instruction manual is available at:
www.lacrossetechnology.com/k86326
Protected under U.S. Patents:
5,978,738
6,076,044
6,597,990
Contact Support: 1-608-782-1610
Product Registration:
www.lacrossetechnology.com/support/register
FCC Disclaimer:
This Device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) the device must accept any interference received, including interference that
may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO
OPERATE THE EQUIPMENT
All rights reserved. This handbook must not be reproduced in any form, even in
excerpts, or duplicated or processed using electronic, mechanical or chemical
procedures without written permission of the publisher.
This handbook may contain mistakes and printing errors. The information in this
handbook is regularly checked and corrections made in the next issue. We accept
no liability for technical mistakes or printing errors, or their consequences.
All trademarks and patents are acknowledged.
Printed in China