KTM 200 SX Motorcycle User Manual


 
ENGLISH
33
Replacing the front brake pads *
Press the brake caliper toward the brake disk, to put the brake piston in its
basic position. Remove clips
1 and pull out bolt 2. Remove brake pads
from the brake caliper. Clean the brake caliper and the brake caliper support
with compressed air. Check the sleeves of the guide bolts for damage, and
grease guide bolts if necessary.
Mount the right brake pad and fix it with the bolt. Mount the left brake pad
and insert the bolt until it stops. Mount the clips.
When mounting the brake pads, be sure to check for correct fit of the
sliding metal-sheet
3 in the caliper support and of the leaf spring 4.
ƽ
WARNING
ƽ
–I
TISVERY IMPORTANT TO KEEP THE BRAKE DISK FREE FROM OIL AND FATTY MATTERS.
O
THERWISE, THE BRAKING EFFECT WOULD BE STRONGLY REDUCED.
–A
FTER ASSEMBLY
, CHECK IF CIRCLIPS HAVE BEEN FITTED CORRECTLY.
AFTER WORKING ON THE BRAKING SYSTEM
,
ALWAYS ACTUATE THE HAND BRAKE LEVER
OR FOOT BRAKE LEVER
,
RESPECTIVELY TO ENSURE THAT THE BRAKE PADS WILL LIE
AGAINST THE BRAKE DISK AND THE PRESSURE POINT IS ESTABLISHED
.
Changing the basic position of the foot brake pedal *
The basic position of the foot brake pedal can be altered by turning the stop
screw
5. The free play at the foot brake pedal must then be adjusted by
means of the piston rod
6.
Measured on the outside, the foot brake pedal must have 3-5 mm
(0.12–0.20 in) of free play before the piston rod can move the piston in the
brake cylinder (to be recognised from the resistance on the foot brake
pedal).
!
CAUTION
!
IF THIS FREE PLAY IS NOT PRESENT, THEN PRESSURE CAN BUILD UP IN THE BRAKE SYSTEM
WHEN DRIVING
, CAUSING THE REAR WHEEL TO BRAKE.THE BRAKING SYSTEM OVERHEATS
AND MAY EVEN FAIL COMPLETELY IN EXTREME CASES
.
Checking the rear brake fluid level
The reservoir for the rear brake disk is located on the right side of the
motorcycle on the rear brake cylinder.
No air bubble should be visible in inspection glass
A when the vehicle is
parked in a vertical position.
ƽ
WARNING
ƽ
I
F THE BRAKE FLUID LEVEL DROPS BELOW THE MINIMUM EITHER THE BRAKE SYSTEM HAS A
LEAK OR THE BRAKE PADS ARE COMPLETELY WORN
. IN THIS CASE, CONSULT AN AUTHO-
RIZED KTM DEALER IMMEDIATELY.
Refilling the rear brake fluid reservoir *
Add brake fluid as soon as a bubble is visible in inspection glass A.
To top up, remove screw
7. Fill DOT5.1 brake fluid (e.g. Motorex Brake
Fluid 5.1) up to the mark B on the inside of the reservoir and remount the
screw. Spilled brake fluid must be rinsed off with water.
ƽ
WARNING
ƽ
–N
EVER USE DOT5 BRAKE FLUID! ITISBASED ON SILICONE OIL AND OF A PURPLE
COLOR
. SEALS AND BRAKE HOSES MUST BE ESPECIALLY ADAPTED TO IT.
–STORE BRAKE FLUID OUT OF REACH OF CHILDREN.
–B
RAKE FLUID CAN CAUSE SKIN IRRITATION. AVOID CONTACT WITH SKIN AND EYES. IF
YOU GET BRAKE FLUID IN YOUR EYES
, RINSE WITH PLENTY OF WATER AND CONSULT A
DOCTOR
.
!
CAUTION
!
–DONTLET BRAKE FLUID GET IN CONTACT WITH PAINT, IT IS AN EFFECTIVE PAINT
REMOVER
.
–U
SE ONLY CLEAN BRAKE FLUID TAKEN FROM A TIGHTLY SEALED CONTAINER.
3
4
3-5mm
A
6
5
7
B
1
1
2
2