Edelbrock 4768 Automobile User Manual


 
©2006 Edelbrock Corporation
Brochure #63-0037Page 1 of 3
Catalog #4760, 4761, 4764, 4765, 4767, 4768
Rev. 1/06 - RS/mc
®
VICTOR X INTAKE MANIFOLDS
For Honda/Acura B-Series Engines
Catalog #4760, 4761, 4764, 4765, 4767, & 4768
INSTALLATION INSTRUCTIONS
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this
installation, it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical
Hotline at: 1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at edelbrock@edelbrock.com
.
IMPORTANT NOTE: Proper installation is the responsibility of the installer.
Improper installation may result in poor performance and engine or vehicle damage.
W
ARNING: When working around gasoline or with any fuel system, always work in a well-ventilated area. Keep all sparks, open
flames, or other sources of ignition away from the work area. Failure to do so could result in a fire or explosion causing vehicle
or property damage, personal injury, and/or death.
PLEASE complete and mail your warranty card. Be sure to write the model number of this product in the "Part #____" space. THANK YOU.
DESCRIPTION: Edelbrock Victor X intake manifolds are designed to optimize horsepower gains for Honda race engines when operating in the
7,000 to 10,000+ rpm range. Specific applications are listed below. These manifolds feature five-inch long, tapered runners and a large, round
plenum for optimal airflow on both all motor, and forced-induction applications. The 66mm machine-profiled throttle body opening fits oversized
throttle bodies without grinding. Victor X manifolds will accept either a GSR or a standard idle air motor, and include Civic / Integra Type R throttle
cable bracket bosses. Model numbers 4760, 4764, and 4767 include four extra fuel injector bosses, which must be machined to add a secondary
fuel system. The 4761, 4765, and 4768 include already machined secondary fuel injector bosses and a machined fuel rail.
NOTE: Victor X manifolds move the throttle body by several inches. The air inlet system you are using may require modification.
APPLICATIONS:
KIT CONTENTS:
1 Intake Manifold
1 Throttle Body Gasket
1 Manifold Air Temp (MAT) Sensor Block Off Plate
1 MAT Sensor Block Off Plate Gasket
2 M5 x 12mm Long Torx Head Capscrews with Integral Washers
(For MAT Sensor Block-Off Plate)
3 .68” O.D. x .281” I.D. x .315” Thick Fuel Rail Spacers
1 17mm Hose x 3/8” Pipe Fitting with 1/8” Pipe Side Port
1 3/8” Hose x 1/4” Pipe Fitting
1 3/8” Hose x 1/8” Pipe Fitting
2 3/16” Hose x 1/8” Pipe Fitting
1 5/16” Hose x 1/8” Pipe Fitting
INTAKE MANIFOLD APPLICATION
4760, 4761 Honda/Acura vehicles using the B18C1 engine. Typically found in 1994-2001 Acura Integra GSR
4764, 4765 Honda/Acura vehicles using the B16A (USDM or JDM) or the B18C5 (Type-R) engine. The B16A is
usually found in the Honda Del Sol VTEC or 1999-2000 Honda Civic Si. The B18C5 is original
equipment for the Acura Integra Type-R.
4767, 4768 Honda/Acura vehicles using a B18 series, non-VTEC engine. These are usually referred to as the “LS”
engine. These engines are commonly found in 1990-2000 Acura Integra GS, RS, or LS models.
4 1/8” Pipe Plug
2 1/4” Pipe Plug
1 3/8” Pipe Plug
1 12” Length of 18-Gauge Yellow Wire
(4760/4761 ONLY)
1 12” Length of 18-Gauge Blue Wire
(4760/4761 ONLY)
4 Wire Connectors
(4760/4761 ONLY)
1 B16 Throttle Cable Bracket
(4764/4765 ONLY)
1 Fuel Rail
(4761/4765/4768 ONLY)
2 Fuel Rail Adapters
(4761/4765/4768 ONLY)
4 1/4-20 x 3/4” Allen Head Screws
(4761/4765/4768 ONLY)
2 1/4-20 x 1-1/8” Hex Head Screws
(4761/4765/4768 ONLY)
2 1/4” Split Lock-Washers
(4761/4765/4768 ONLY)