Filter
Top Products
MAN# 650284:E
PERF
PERF PERF
PERF Performance menu setup
The performance readings can be turned on or off. When they are turned off the odometer display will only toggle through the
mileage readings.
• Press and release the switch until “PErF” is displayed, then press and hold the switch until “ - ” is displayed.
• Release the switch. The current setting will be displayed (on or oFF).
• Press and release the switch until the desired setting is displayed.
•
Press and hold the switch until “ - ” is displayed to save the setting.
FUE
FUEFUE
FUEL
LL
L Low fuel light setup
• Press and release the switch until “FUEL” is displayed, then press and hold the switch until “ – ” is displayed.
• The display will show “OFF”, “DYN”(2004-2008 Dyna), “SPo”(Sportster), or “d09” (2009-up Dyna). 2004-2008 Dyna should be used if
there is a stock fuel gauge and it is 2008 or older. If it has a stock fuel gauge and it is 2009 or newer use 2009-up Dyna.
Sportster should be used when there is only a low fuel switch. Press and release the switch to change to the desired setting.
•
Press and hold the switch until “ - ” is displayed to save the setting.
odoMK
odoMKodoMK
odoMK Odometer preset
The odometer can be preset by the customer within the first 100 miles. Once the odometer has more than 100 miles, the menu
option will no longer be displayed. Make sure you have correctly selected the units to be either MPH or km/h first. The odometer will
be set in the selected units. Once you have preset the miles you cannot change it again.
WARNING!!: This only allows setting odometer to the nearest mile. Do not use tenths! For example a mileage of 65432.1
should be set to “065432” using this method. If the tenths digit is used, the odometer will read 10 times too high.
• Press and release the switch until “-odoMK” is displayed, then press and hold the switch until “ - ” is displayed.
• The current miles will be displayed with the left most digit flashing.
• Press and release the switch to increment the digit. Press and hold the switch to move to the next digit to the right.
• Continue until the right most digit has been set. Press and hold the switch and the speed display will show “No”.
• Press and hold the switch while “no” is displayed to go back and continue changing the odometer display. Turn the key off to
cancel any changes.
• Press and release the switch to change to speed display to “yes”. Press and hold the switch while “yes” is displayed to save the
current odometer reading.
FUNCTION SWITCH
The function switch on the side of the dash panel allows access to all of the mileage, rpm, and performance
information. Pressing and releasing the function switch toggles through the different displays. Press and holding the
switch will reset the current display. The display sequence is as follows:
ODOMTR > 000000 odometer mileage
TRIP A >
A
000.0 trip meter mileage A
TRIP B >
B
000.0 trip meter mileage B
SERVIC > S 0000 miles since last service (if programmed)
KPH > ++++++ metric speed conversion (to mph if metric unit is selected)
VOLTS > 00.0
V
displays voltage to gauge
* HI SPD > HI 00 high speed recall
* 0-60 T > 60 00.0 0-60mph time (0-100kph)
* QUARTR > 25 00.0 quarter mile time
* QT MPH > 25 00 quarter mile speed
CLOCK > 12:00 12 hour clock
* HOURS > HR 0.0 re-settable hour meter
RPM > 0000
RPM
rpm reading in alpha display
* HI RPM > H 0000 high rpm recall
TEMP > 000 F temperature reading, “C” if metric
The 0-60 and ¼ mile timers are zeroed by pressing and holding the switch while that timer is displayed. The timer will not
restart until the speed reaches zero and you start driving again.
Display functions with a ‘*’ in front of them are only shown with performance readings turned on.