Filter
Top Products
STITCH LINE
To Attach Rainfly continued
3. Insert end of each black Rainfly Pole into pin on either side of front
door. (Fig. 10 & 10A)
4. Go to opposite end of Rainfly Pole and gradually apply pressure to
form an arch. Insert the pin into pole end at other side of the door.
(Fig. 10 & 10A)
5. Locate all
hook & loop fasteners on underside of Rainfly and wrap
around black and grey poles to secure. (Fig. 10B)
6. Stretch elastic straps and hook clip on each to the metal loops at
the front and back of the tent. (Fig. 10C)
7. Extend out vestibule flaps and secure with metal stakes through the
loops in the web straps (Fig. 10 & 5D)
8. Stretch guylines until taut, then secure with stakes. (Fig. 10 & 10E)
The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN CHINA • PRINTED IN CHINA
© 2008 The Coleman Company, Inc.
Coleman
®
, , and are registered trademarks and Montana
TM
is a trademark of
The Coleman Company, Inc.
4010003991 (20080928)
Self-rolling Windows
CAUTION: “Springs” may have sharp edges. Handle with care to avoid
injury. Keep out of reach of children.
NOTE: Carefully unroll metal “springs” stored in bag with stakes. The
color marking on each “spring” should match the color of the fabric
“flag” sewn to the window or door sleeve opening. (Fig. 11)
1. Locate sleeve(s) in window panel, open hook & loop fastener; then
insert “spring(s)” with matching color marking. (Fig. 11 & 12)
NOTE: When inserting into the sleeve(s), the
color marking on the “spring(s)” should always
face the operator.
2. Close hook & loop fastener to secure.
3. Before unzipping and opening the window,
push in at top to engage “spring(s)” to activate
the self-rolling feature. (Fig. 13)
4. Unzip to allow the window panel to roll down
automatically; zip back to close window panel.
(Fig. 14 & 15)
NOTE: Repeat steps above for inserting the color
matching “spring(s)” into sleeve(s) for the rest of
the windows.
Fig. 11
Sleeve
Color “Flag”
Door
Window
Panel
Window Panel
Push in at top
to engage
“spring(s)”
Color
Dot
Fig. 13
Fig. 12
Sleeves
Fig. 14
Fig. 15
Color
“Flag”
Tent Lighting System
Your tent comes pre-wired with the Coleman
®
Tent
Lighting System. See manual that came with the light
and carefully read all instructions before use then save
for future reference.
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your tent. Condensation is caused by water
vapor from your breath, perspiration, or any wet clothing inside the tent.
It is NOT LEAKAGE through the shelter fabric. It can be minimized by
removing wet clothing from your shelter and by providing good ventila-
tion through the tent.
• Tree limbs, tree sap, bird droppings, or moisture steadily dripping off
tree limbs can cause damage to the tent fabric and its coating resulting
in leaks or loss of flame-resistant properties.
• Never store tent, even for a short period of time, without drying it
thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.
• Stakes should be removed by pulling on the stake itself. NEVER PULL ON
THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY
DAMAGE OR PERSONAL INJURY.
• Tent poles should not be left telescoped together during storage.
• Do not leave your tent set-up for weeks at a time. Be aware that exposure
to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this shelter fabric.
This shelter meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
Self-rolling Windows continued
CAUTION: All “springs” must be removed from sleeves before tearing
down tent to avoid damage to the tent fabric or part. To avoid injury,
carefully roll up “springs”. Keep out of reach of children. Store rolled
“springs” in bag with stakes.
Cooler Access
The smaller zippered opening at the side of tent is
designed for added ventilation and easy access to
your beverage cooler.
1. To use as a vent, unzip flap to expose screen.
2. To use as a cooler access, unzip other flap to
make an avenue to bring beverages into tent. (Fig. 17)
To Store
1. All “springs” must be rolled up and placed in bag with stakes.
2. All poles and stakes must
be placed in the storage bag to prevent
damage to the fabric items placed in the carry case.
3. Make sure tent is clean and dry before placing in carry case.
4. Remove rainfly, spread out on floor of tent, then unzip door & vents
before taking tent down for storage.
5. Neatly fold tent to width of pole storage bag, place on tent, roll
tightly, and place in carry case.
5. Store in a clean, dry area.
Electrical Cord Access
1. Unzip the access panel in the lower
left corner of tent and bring in an
electrical cord.
NOTE: Use only UL approved cords
rated for outdoor usage. (Fig. 16)
Fig. 17
Fig. 16
Fig. 10
10A10B
10C
10E
10D
Guylines