Filter
Top Products
Main te nance
Your Clifford system requires no maintenance except for periodic replacement of the remote control batteries. This product, like any electrical device in
your vehicle, requires your car battery be in proper working order and fully charged. To ensure pro per operation, periodically have your vehicle battery
“load-checked” at any local garage/mechanic. Also make sure the battery cables and connections are tight and free from corrosion.
Wel come to the world of
high- technology ve hi cle se cu rity and con ven ience
C
ongratulations on the purchase of your Clifford Electronics mobile security/convenience system. Clifford Electronics has long been recognized as the
leading manufacturer of high-technology vehicle security systems. Our commitment to technological innovation, quality and reliability is clearly evident
in your Clifford system. Yet despite all its sophistication, your system is amazingly easy to use, never more difficult than a few presses of a button.
Your re mote con trols
The two 4-button remote controls are sophisticated miniature radio transmitters each powered by a 3 -volt lithium battery. A weak remote control battery
will reduce range (the system will warn you if the battery in your remote is nearing the end of its useful life, see the Low battery warning section for details).
Electrical/radio frequency interference, obstructions, weather conditions and even sunspots can interrupt the signal from your remote to the system.The
remote controls are the keys to your system. But these remote controls are much more secure than ca r keys because each incorporates our ACG 2
(Anti-CodeGrabbing 2) technology with trillions of digital codes for the ultimate protection agains t remote control cloning devices. You will use your
Concept 100 remote control to arm and disarm the system, lock and unlock the doors, activate/deacti vate the panic feature, enable/exit valet mode and
command options such as a remote trunk release, power window control, electric garage door interface or even remote starting of the engine and heater or air
conditioner, among other options.
Re motely con trol ling your Clif ford system
TO ARM:
Press button . Upon arming: two siren chirps, two parking light flashes, dashboard LED flashes repeatedly and doo rs lock.
TO DIS ARM:
Press button . Upon disarming: one chirp, one parking light flash, LED turns off, doors unlock and the interior l ights turn on.
TO ARM OR
DIS ARM SI LENTLY:
Simultaneously press both the button and the ✱ button to arm or disarm without chirp acknowledgments.
TO PANIC:
For three seconds, continually press button . The parking lights will flash repeatedly and the siren will blare for 30 seconds
(American model) or until you press the button again (European model). If the ignition is on (indic ating you are in the car), the
doors will automatically lock to prevent an assailant from entering (note: some vehicles are unable to lock the doors while the
ignition is on). If the ignition is off, the doors will unlock, allowing you to enter immediately without fumbling with your keys.
TO RE MOTELY
OPEN THE TRUNK:
If you have this option, press button while the system is in its disarmed state.
TO RE MOTELY TURN
ON HEADLIGHTS:
If you have this option, press button to turn on the headlights for 10-seconds.
TO RE MOTELY
START THE EN GINE:
If you have this option, press button ✱ to remotely start the engine (or shut it down if idling under the control of IntelliStart 4).
Before remote starting, be sure to see the Remote Engine Starting DOs and DON’Ts noted in the IntelliStart 4 user’s manual.
TO TURN VALET
MODE ON OR OFF:
Simultaneously press buttons and ✱ to enable/exit valet mode.
TO RE MOTELY OPEN
OR VENT WIN DOWS:
If you have this option, press buttons and after disarming to fully open the windows controlled by SmartWindows 4.
On hot days, press this button combination right after arming to vent the windows slightly while th e system remains armed.
ACG 2 (Anti- CodeGrabbing 2™)
ACG 2 protects you and your automobile from code-grabbing devices. Code-grabbers record, from hundr eds of feet away, the code sent by your car alarm
remote control (code-grabbers are very similar to, but simpler than, cellphone “cloning” devices). The thief then plays back the code when you’re gone,
instantly disarming the alarm and unlocking the doors. It’s like leaving your keys and remote in th e door. Many non-Clifford alarms can be defeated that
easily, and some of the latest “smart” code-grabbers can even decipher the code hopping/jumping seq uence used by other car alarm manufacturers. In
contrast, your Concept 100 uses complex digital signal processing and unbreachable code encryption to randomly change the digital code every time you
use the remote control. Your remotes will never transmit the same code twice, and the control unit will never accept the same code twice. Thus the code
played back by the code-grabber — even the latest generation smart code-grabbers — will never be accepted by your Concept 100 system.
Auto matic re mote con trol low- battery warn ing
If your remote control battery is low, you’ll hear a rapid 5-chirp sequence when you disarm instead of the usual one chirp (with the Self-Powered SmartSiren 4
option, you’ll hear a low-pitched chirp). Replacement batteries are available from any Authorized Clifford Dealer.
3