Filter
Top Products
8
USING THE LED AREA LIGHT
The LED Area Light is controlled by the Area Light ON/OFF Push button on the
top panel of the unit (see page 6). Make sure the LED Area Light is turned OFF
when the unit is being recharged or stored.
CARE
AND MAINTENANCE
This product has sealed lead acid batteries that should be kept fully charged.
Recharge before first use, immediately after each use, or at least once a month
if not in frequent use. Failure to do this may reduce the battery life dramatically.
Note: This unit is delivered in a partially charged state – you must fully
charge it before using it for the first time. Initial AC charge should be for 15
hours.
Use only mild soap and damp cloth to clean the tool. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment (other than those listed in this manual) should be performed by
authorized service centers or other qualified service personnel, always using
identical replacement parts.
CHARGING/RECHARGING
For maximum battery life, we recommend the unit be kept fully charged at all
times. To charge this unit, use only the supplied AC Charging Adapter or the
built-in 12 Volt DC Adapter Plug.
Note: Recharging battery after each use will prolong battery life; frequent heavy
discharges between recharges and/or overcharging will reduce battery life.
120 Volt AC Recharge
1. Turn the unit ON by pressing the ON/OFF Power Push button. The unit will
beep once and the red Power LED Indicator and Battery Status LED Indicator
will light.
2. Connect the barrel tip of the 120 Volt AC Charging Adapter into the 12 Volt
DC Charging Port at the top of the unit (
see “Controls and Indicators” on page 6).
3. Plug the other end of the cord into a standard North American 120 volt AC
wall outlet.
4. Press the Recharge Unit Push button. The unit will beep once again and the
Battery Status LED Indicator will
flash green
, indicating the unit is
charging
.
5. When the Battery Status LED Indicator stops flashing and
lights green
steadily
, the unit is
fully charged
.
6. When charging is complete, disconnect the 120 Volt AC Charging Adapter
and store in a safe place.
12 Volt DC Recharge
1. Turn the unit ON by pressing the ON/OFF Power Push button. The unit will
beep once and the red Power LED Indicator and Battery Status LED Indicator
will light.
7
5. When the Vehicle Boost LED Indicator stops flashing and
lights green
steadily and the unit beeps continuously,
(generally, after approximately
15 minutes), the
vehicle battery has been boosted.
Turn the vehicle
ignition and crank the engine in 5-6 second bursts until engine starts.
6. After use, turn the
BB7B
OFF by pressing the ON/OFF Power Push button
and recharge the unit as soon as possible so it is ready for the next
emergency (see the “Charging/Recharging” section on page 8).
Notes: The Simple Start
™
will NOT function in boost mode while the unit is
recharging, the 12 Volt DC Outlet is in use, or if the 12 Volt DC Outlet cover
is open. Some vehicles require that the car be started in order to use the
12 volt DC accessory outlet. Simply turn the ignition switch to the
accessory position before connecting the Simple Start
™
.
WARNING: TO REDUCE THE RISK OF INJURY:
• Make sure the unit is disconnected from all charging power sources
before beginning the jump-starting procedure.
• Use this power system ONLY on vehicles with 12 volt DC battery systems
and negatively-grounded vehicles.
• Do not operate unit if there is any evidence of damage. The product must
be returned to the manufacturer for testing and repair. Replace any
damaged charging adapters immediately before further use.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Vehicles that have on-board computerized systems may be damaged if vehicle
battery is jump-started. Before jump-starting this type of vehicle, read the
vehicle owner’s manual to confirm that external-starting assistance is advised.
• Excessive engine cranking can damage the vehicle‘s starter motor. If the
engine fails to start after the recommended number of attempts (refer to
the vehicle’s owner manual), discontinue jump-start procedure and look for
other problems that need to be corrected.
USING THE 12 VOL
T DC PORTABLE POWER SUPPLY
This portable power supply is for use with all 12 volt DC accessories
equipped with a male accessory outlet plug and rated up to 5 amps.
1. Check to ensure that the 12 Volt Plug is stored in the compartment. If
not, store it in the compartment.
2. Turn the unit On by pressing the ON/OFF Power Push Button and lift up
the cover of the unit's 12 Volt DC Outlet.
3. Insert the 12 volt DC plug from the appliance into the 12 Volt DC
Accessory Outlet on the top of the unit. DO NOT EXCEED A 5 AMP LOAD.
4. Switch on the appliance and operate as usual.
Note: Do not attempt to use the Simple Start
™
or recharge the unit while the
12 Volt DC Outlet is in use.
BB7B_Manual EN_082406 8/24/06 10:14 AM Page 7