Support User Manuals

Audiovox 07S3BP Remote Starter User Manual

Open as PDF

of 20

128-8111

4 of 20

Action System Response

Turn ignition on No response

Press and release the valet switch 3 times 1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps

This Action Accesses Feature Bank 3 Remote Start Selectable Features

First Press the valet switch one time 1 chirp = defrost output pulsed

Press transmitter Lock button to change 2 chirps = defrost output 10 Mins

or

Second Press and release the valet switch 2 chirps = RF start chirp on

Press transmitter Lock button to change 1 chirp = RF start chirp off

or

Third Press and release the valet switch 2 chirps = run time set for 10 mins

Press transmitter Lock button to change 3 chirps = run time set fro 15 mins

Press transmitter Lock button to change 4 chirps = run time set for 20 mins

Press transmitter Lock button to change 1 chirp = run time set for 5 mins

or

Fourth Press and release the valet switch 1 chirp = parking lights on steady w/RS active

Press transmitter Lock button to change 2 chirps = parking lights flashing w/RS active

or

Fifth Press and release the valet switch 2 chirps = tachometer input checking

Press transmitter Lock button to change 1 chirp = voltage sense input checking

or

Sixth Press and release the valet switch 1 chirp = greater than 0.5 V check before start

Press transmitter Lock button to change 2 chirps = less than 0.5 V check before start

or

Seventh Press and release the valet switch 2 chirps = ign 2 on during crank

Press transmitter Lock button to change 3 chirps = ign 2 same as accessory

Press transmitter Lock button to change 1 chirp = ign 2 off during crank

or

Eighth Press and release the valet switch 2 chirps = ign 3 on during crank

Press transmitter Lock button to change 3 chirps = ign 3 same as accessory

Press transmitter Lock button to change 1 chirp = ign 3 off during crank

or

Ninth Press and release the valet switch 1 chirp = diagnostics off

Press transmitter Lock button to change 2 chirps = diagnostics on

or

Tenth Press and release the valet switch 2 chirps = crank time 1.0 sec

Press transmitter Lock button to change 3 chirps = crank time 1.5 sec

Press transmitter Lock button to change 4 chirps = crank time 2.0 sec

Press transmitter Lock button to change 1 chirp = crank time 0.8 sec

or

Eleventh Press and release the valet switch 1 chirp = unit set for gasoline engine

Press transmitter Lock button to change 2 chirps = unit set for diesel engine 10 sec delay

Press transmitter Lock button to change 3 chirps = unit set for diesel engine 15 sec delay

Press transmitter Lock button to change 4 chirps = unit set for diesel engine 20 sec delay

or

Twelfth Press and release the valet switch 1 chirp = transponder output while R/S active

Press transmitter Lock button to change 2 chirps = transponder output during start only

Press transmitter Lock button to change 3 chirps = transponder output until ignition turned off

or

Thirteenth Press and release the valet switch Non Functional On This Unit

or

Fourteenth Press and release the valet switch 1 chirp = crank averaging w/voltage input checking

Press transmitter Lock button to change 2 chirps = preset crank time w/voltage input check

or

Fifteenth Press and release the valet switch Non Functional On This Unit

or

Sixteenth Press and release the valet switch Non Functional On This Unit

or

Seventeenth Press and release the valet switch 1 chirp = aux o/p Black/Blue single pulse

Press transmitter Lock button to change 2 chirps = aux o/p Black/Blue as alarm feature #1

Press and release the valet switch or turn

the ignition off to: Exit Programming Mode

Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the

programming will be terminated.

4

previous next