Filter
Top Products
Optional Accessories
Batteries
S-1430 Alkaline D-Cell Batteries; set of 10 ..............................................$26.00
S-1465 NiCad battery pack; 4.3 amp hours ..........................................$165.00
Power Supply
S-1460 International AC Adapter/Recharger;110/220 volt s;50/60 Hz. ......$109.00
W ireless Kit s
S-1600 W ireless Lapel Mic Kit ..............................................................$308.00
S-1610 W ireless Headset Mic Kit ..........................................................$374.00
S-1612 W ireless Lapel/Headset Mic Kit ..............................................$374.00
S-1620 W ireless Hand-Held Mic Kit ......................................................$374.00
Microphones
S-2030 Lapel Mic; with 12 f t. extension ..................................................$55.00
S-2040 Headset Mic; with 12 f t. extension ............................................$121.00
S-2030A Hand-Held Mic and Cable ..........................................................$99.00
S-1720 Mic Extension Cord; 25-ft...........................................................$65.00
Extra Speaker & Tripod
S-1201 Compact Companion Speaker; black high pressure laminate ........$209.00
S-1090 Tripod for speaker ....................................................................$188.00
Light
S-1100 AC Reading Light; clip-on ............................................................$55.00
Media Cart Base
S-260 Combines with Tabletop Lectern to form a full-size lectern
or use separately for slide projector, etc...................................$197.00
Prices are subject to change without notice
10. Attach the gooseneck. Screw the
gooseneck with mic holder onto the
gooseneck flange. Insert the mic cord
into the mic base. Place the mic into the
mic holder; insert the mic plug into the
dynamic microphone jack.
11. Plug-in the speaker. Plug the speak -
er cord into either the right or lef t amp
jack. If you have a second external
speaker, connect it s 1/4 plug into the
S peaker- R jack Set the amplifier inside
the lectern.
12. Att ach the speaker grille by pressing
it s post s into the holes on the front of the
lectern.
Refer to the S-805A amplifier operating
instructions for information about the amp
controls.
If you purchased any optional acces -
sories such as a wireless kit, lapel mic,
International AC Adapter/Recharger,
extra speakers, tripods, etc. refer to the
instructions p acked with them for inst alla-
tion and usage information.
Y our Tabletop Lectern is now complete.
Thousands of AmpliVox sound products
have been in use since we first began
shipping in 1961. We hope you enjoy
many years of use from your new
Tabletop Lectern.
If you have any questions or comments,
call customer service line.
1-800-267-5486
6. Att ach the front/speaker p anel. Make
sure the finished edge of the speaker/front
panel is facing up towards you. Slide
speaker/front p anel until the dowel pins of
the right and lef t side p anels are com-
pletely inserted into the Quick-fit connec -
tors of the speaker/front p anel. T ighten the
4 Quickfit Connectors in speaker/front
p anel 1/2 turn.
7. Att ach the bottom. Carefully pick up
and place the Top, Right and Lef t side
panel assembly on it s side with the Top
panel facing opposite of you. Insert the
Bottom Panel under the pins on the Right
and Left side p anels by sliding the bottom
panel under pins of the sides. Now slide
the bottom panel until the dowel pins of the
side p anels are completely inserted into
the Quick-fit connectors of the bottom
p anel. T ighten the 4 Quickfit Connectors
on the bottom panel 1/2 turn.
8. Carefully turn over lectern Af ter tighten -
in g Expando Connectors on the bottom of
the lectern, Carefully pick up and turn
over lectern so that the Paper Stop is fac -
ing up.(see illustration above)
S-250 ONLY
9. Inst all the batteries in the amp. Refer to
the amp instruction sheet for battery
inst allation information.
4. Att ach the lef t side. Place Top panel on
protected flat surface with dowel pins fac -
ing up. Place the lef t side p anel with the
finished edge facing up onto the top p anel
and slide side p anel until it s dowel pins are
completely inserted into the Quick-fit con -
nectors as far as they can go. The short
edge of the side p anel should be towards
the edge of the Top panel that has the
paper stop. Use a phillip s screwdriver
to tighten the 2 Quick-fit Connectors. T urn
only 1/2 turn clockwise. Over tightening
will break the connectors!!
F:\docs\productinstructions\r-
5. Att ach the right side p anel. Attach the
right side p anel using the same instructions
as the lef t side p anel to the top panel and
tighten the 2 Quick-fit Connectors.
Short edge
Top
Lef t Side Panel
T ighten
Short edge
Top
Angled
Side
Lef t Side Panel
T ighten
Paper Stop
Paper Stop
Right Side Panel
Lef t Side Panel
T ighten
Lef t Side Panel
Gooseneck flange
Paper Stop
Angled
Side