Rev. 0.00
3-5
STARLineModeCommandSpecications
ESC GS = n1 n2 da1 da2 … dak db1 db2 … dbk
[Name] Write blank code page data
[Code] ASCII ESC GS = n1 n2 da1 da2 .. dak db1 db2 .. dbk
Hexadecimal 1B 1D 3D n1 n2 da1 da2 .. dak db1 db2 .. dbk
Decimal 27 29 61 n1 n2 da1 da2 .. dak db1 db2 .. dbk
[DenedArea] Thermal : n1 = 0, n2 = 48, 1 ≤ (n1 + n2 x 256)
0 ≤ da ≤ 255 (Font-A data), db = 0 (Star mode does not have Font-B), k = (n1 + n2 x 256)
Slip : -
Validation : -
[Initial Value] Thermal : -
Slip : -
Validation : -
[Function] A blank code page indicates a character code table where character codes from 80h to FFh are all
blank.
A blank code page can be selected using the ESC GS t n command n = 255.
The printer is reset when writing with this command is completed.
[Font-A Data Format Vertical 24 dots x Horizontal 12 dots]
•=Dataregion/○=Zerodata
<Slip>,<Validation>
Only registration is possible.
Registration data is printable after switching to thermal.
Da1 ● ● ● ● ● ● ● ● Da2 ● ● ● ● ○ ○ ○ ○
Da3 ● ● ● ● ● ● ● ● Da4 ● ● ● ● ○ ○ ○ ○
Da5 ● ● ● ● ● ● ● ● Da6 ● ● ● ● ○ ○ ○ ○
Da7 ● ● ● ● ● ● ● ● Da8 ● ● ● ● ○ ○ ○ ○
Da9 ● ● ● ● ● ● ● ● Da10 ● ● ● ● ○ ○ ○ ○
Da11 ● ● ● ● ● ● ● ● Da12 ● ● ● ● ○ ○ ○ ○
Da13 ● ● ● ● ● ● ● ● Da14 ● ● ● ● ○ ○ ○ ○
Da15 ● ● ● ● ● ● ● ● Da16 ● ● ● ● ○ ○ ○ ○
Da17 ● ● ● ● ● ● ● ● Da18 ● ● ● ● ○ ○ ○ ○
Da19 ● ● ● ● ● ● ● ● Da20 ● ● ● ● ○ ○ ○ ○
Da21 ● ● ● ● ● ● ● ● Da22 ● ● ● ● ○ ○ ○ ○
Da23 ● ● ● ● ● ● ● ● Da24 ● ● ● ● ○ ○ ○ ○
Da25 ● ● ● ● ● ● ● ● Da26 ● ● ● ● ○ ○ ○ ○
Da27 ● ● ● ● ● ● ● ● Da28 ● ● ● ● ○ ○ ○ ○
Da29 ● ● ● ● ● ● ● ● Da30 ● ● ● ● ○ ○ ○ ○
Da31 ● ● ● ● ● ● ● ● Da32 ● ● ● ● ○ ○ ○ ○
Da33 ● ● ● ● ● ● ● ● Da34 ● ● ● ● ○ ○ ○ ○
Da35 ● ● ● ● ● ● ● ● Da36 ● ● ● ● ○ ○ ○ ○
Da37 ● ● ● ● ● ● ● ● Da38 ● ● ● ● ○ ○ ○ ○
Da39 ● ● ● ● ● ● ● ● Da40 ● ● ● ● ○ ○ ○ ○
Da41 ● ● ● ● ● ● ● ● Da42 ● ● ● ● ○ ○ ○ ○
Da43 ● ● ● ● ● ● ● ● Da44 ● ● ● ● ○ ○ ○ ○
Da45 ● ● ● ● ● ● ● ● Da46 ● ● ● ● ○ ○ ○ ○
Da47 ● ● ● ● ● ● ● ● Da48 ● ● ● ● ○ ○ ○ ○
(Font - A Data Format Vertical 24 dot x Horizontal 12 dot)
= Data Region / = Zero Data
