Whistler CR85 Radar Detector User Manual


  Open as PDF
of 2
 
WHISTLER FEATURES
1. Bracket Release Button – provides quick
and easy release of the mounting bracket.
2. Speaker – provides distinct audio warnings
for X, K, Ka band radar, safety warning system,
and laser.
3. Mounting Bracket Location – slot holds
mounting bracket firmly.
4. Radar Antenna – compact, high-efficiency
antenna receives radar signals.
5. Front Laser – high gain optical lens
provides increased sensitivity and field of
view for leading-edge laser detection.
6. Rear Laser – an integrated optical
waveguide provides superior detection of
laser signals transmitted from behind.
7. City Button - reduces the annoyance of
false alerts typically encountered in urban
driving areas.
8. Quiet Button - pressingQUIETbeforea
signal is detected engages Auto Quiet Mode
which automatically reduces the audio level after
the initial warning to a low audio level setting.
PressingQUIETduringaradar/laserencounter
silences audio alerts, while allowing visual
alerts to keep you informed.
9. Power / Volume Control – gently press this
button in to turn the unit on/off. Move back or
forwardtoadjusttheaudiolevel.
10. Dim / Dark - engages Dim/Dark modes.
11. Menu Button -entersOptionSelectMode.
12. Text Display – provides distinct visual confirmation
of signals detected, signal strength, and indicates
engaged modes of operation.
13. Alert Periscopes - provide an additional
attention getting visual alert.
14.
Power Jack
–
Provides connection for the
power cord.
FEATURE DESCRIPTIONS
Mounting Guidelines
• Mount the unit as low as possible near the
center of the windshield.
• Do not mount the unit behind wipers,
ornaments, mirrored sunscreens, etc. These
obstructions have metal surfaces which can
affect radar and laser signals and reduce
 criticalwarningtime.(Regulartintedglass
does not affect reception).
• SomewindshieldshaveanInstaclear
™
or
Electriclear
™
type coating, which affect radar
signals. Consult your dealer or the owner’s
manual supplied with your vehicle to determine
if your windshield has this coating.
• Avoid placing the unit in direct contact with
the windshield.
• To reduce the possibility of theft, conceal
the unit when not in use.
IMPORTANT:Makesuretheunitislevel
Windshield Mounting
• Install the two suction cups and rubber bumper
onto the bracket by fitting them into their holes.
• Press the suction cups onto the windshield at the
location you have chosen.
INSTALLATION
Important: Somenewercarshaveaplasticsafety
coating on the inside of the windshield. The
windshield bracket may leave permanent marks on
this type of surface. To find out if your vehicle has
this type of windshield, check the vehicle’s owner’s
manual or ask your dealer. We recommend
that you do not leave the suction cup bracket on
the window in direct sunlight. If the detector is
removed, this may cause blistering of the dash
in some vehicles.
• Slidethedetectorontothebracketuntilitlocksinto
place.
• If necessary, the unit may be leveled by bending
the windshield bracket. Press the bracket release
button and remove the detector before bending.
Power Cord Connection
• Plug the small end of the power cord into the
unit’spowerjack.
• Plug the large end into the vehicle’s cigarette
lighter socket.
Note: Cord fits tightly into detector. When
installing the cord, expect some resistance.
Fuse Replacement
The lighter socket plug is equipped with a
replaceable2amp,3AGfuselocatedbehind
the silver tip. To replace the fuse, carefully
unscrew the tip of the plug.
INSTALLATION
INSTALLATION
Power On Self Test & Volume
To turn the unit ON or OFF, gently press the
center of the Power/Volume button into the side
of the unit. Each time your Whistler detector
is turned on, an automatic self-test sequence
confirms that the speaker and visual displays are
functional.
Audio Level Adjustment
Tochangetheaudiolevel:
• Move Power/Volume button back to increase
audio level.
• Move Power/Volume button forward to
decrease audio level. As audio level is
adjusted,beepsareprovidedandthedisplay
indicates volume level.
Auto Quiet Mode
Auto Quiet mode reduces the selected audio
leveltolevel(1)approximately5secondsafter
a radar or safety warning system
™
signal is
detected. The alert for any new signal within
20secondswillresumeatlevel(1).AutoQuiet
mode does not affect laser alerts.
• PressQuiet(beforeasignalisdetected)to
engage Auto Quiet mode.
•OncetheAutoQuietmodeisengaged,you
may cancel the audio alarm by pressing Quiet.
•PressQuiet(whentheunitisnotalarming)to
cancel Auto Quiet mode.
Quiet Mode
Quiet mode cancels audio during an alert
and any new alert within20seconds.After20
seconds of no radar signal detected, the audio
alerts are restored.
•PressQuiettocanceltheaudio.
•Press Quiet a second time during an alert to
restore the standard audio alert pattern.
OPERATION
City/City 1/City 2 Mode
Whistler’sThreeStageCityModeisdesigned
to reduce the annoyance of automatic door
openers, intrusion alarms and other devices which
share frequencies with police radar. Generally, X
band is used for these devices.
•PressCitybuttontocancelHighwayMode
and engage City Mode.
•PressCitybuttonagaintoenterCity1Mode.
•PressCitybuttonagaintoenterCity2Mode.
•PressCitybuttonafourthtimetocancelCity2
Mode and returns the unit to Highway Mode.
In City Mode, weak speed/safety warning
system
™
signals give an initial alarm of two
beeps, and then remains quiet unless the signal
becomes very strong. When the signal strength
increases, two additional beeps are provided.
City1andCity2Modesoperatethesameas
HighwayMode,butinCity1Mode,onlythe
Xbandsensitivityislowered.InCity2Mode,
X-band is not detected.
Caution: Sometowns/smallcitiesmaystillbe
using X band radar. City Modes do not change
the audio alert for laser.
Highway Mode
Highway mode provides full audio warnings
anytimeradar(X,K,Ka,SafetyWarning
System
™
) or laser signals are detected, and is
recommended for open road driving.
OPERATION
Alert Periscopes
Whistler’s Alert Periscopes provide an added
attention getting visual alert. The two extra LEDs
flash on and off when the unit alarms to provide a
unique visual alert. This alert can be programmed,
throughtheOptionSelectModeto:1.flashforall
alarms,2.remainon, or 3. turn LEDs off completely.
Dim/Dark Mode
Dim/Dark Mode reduces the illumination of the
display.
• Press the Dark button to reduce illumination
to a Dim setting.
• Press the Dark button a second time engages
Dark Mode. The display illumination is further
reduced.
Dim or Dark Mode can be engaged during an
alert. In Dark Mode, the display goes dark for
aslongasasignalisbeingdetectedandfor20
seconds after, then the display returns to the
dimmer setting.
• Press the Dark button a third time to restore
full illumination to the display.
Selectable Vehicle Battery
Saver Mode
TheVehicleBatterySaverModeautomaticallyshuts
off your detector within 3 hours. The timer is reset if
the detector is turned off, unplugged or any button
is pressed before the timer has expired. The detector
will alert you with an audible and visual warning
before it shuts off. During this warning, you can
momentarily reset the timer by pressing any button. If
the unit has automatically turned off, press the Power
button to turn the unit back on.
Referto“Option
SelectMode”forinstructionsforchangingthe
battery saver mode options.
OPERATION
OPERATION
X/K and Ka Filter Modes
There are times when a radar detector in another
vehicle, can emit a frequency which can cause your
detector to falsely alert. These Filter Modes allow you
to select the level needed for your area to minimize
the occurrences of these false alerts. X/K and Ka Filter
Mode factory default settings should provide adequate
filtering for most conditions. If you experience excessive
alerts due to radar detectors in other vehicles, increase
theFilterlevelforthebandreceived.SeeOption
SelectionModetochangethefiltersettings.
Ka Max Mode
Ka Max Mode provides enhanced Ka sensitivity -
increased protection. This mode can be selected with
orwithoutRSID.SeeOptionSelectModeforchanging
Ka options.
Traffic Flow Signal Rejection (TFSR)
Recently,manynewproductsoperateonXorKband
causingnuisancealertstoradardetectors.Someof
theseareradarbasedTrafficMonitoringSystems
mounted to poles alongside the highway and others
areKBandLaneChangeAssistantsandBlindSpot
Detectors found on some automobiles. When turned
on in option mode, helps eliminate excessive alerts from
erroneous X and K-band sources. Traffic flow monitoring
systems are getting more common. Many of these
systems generate radar signals to measure the flow of
traffic across multiple lanes. Most detectors will alert
youtoitunnecessarily.Thisrejectionfeatureexamines
the incoming signal and will aid in reducing the alerts to
such sources.
We suggest you turn TFSR on if you are experiencing excessive
X or K band false alerts every half mile or so along stretches of
roadway that contain these traffic flow sensors.
Option Select Mode
PresstheMenubuttontoenterOptionSelectMode.
Each press of the Menu button changes to the next
selectable feature.The Dark (D) button and the Quiet
(Q) button turns the feature ON/OFF or Blinking for
example.Abuttonmustbepressedwithin20seconds
orOptionSelectModewillautomaticallybeexited.(See
page 13 for chart)
OPERATION
Stay Alert Feature
TheStayAlertFeatureisdesignedtotestadriver’s
alertness.Toengage(whentheunitisnotalarming):
• PressandholdtheCitybuttonfor
approximately2seconds.Releasethebutton
during or immediately after the alert is given.
DISPLAYSHOWS:
Within 30-60 seconds, two beeps are sounded; to
show alertness, the driver must press either the City,
Menu, or Quiet buttons within 3-5 seconds. If a button
is pressed within 3-5 seconds, the cycle is repeated.
If a button is not pressed within 3-5 seconds, an
alarm sounds.
DISPLAYSHOWS:
• PresstheDarkbuttontoexittheStayAlert
feature.
WARNING!!!
StayAlertisNOTintendedasa
substitute for adequate rest. You should NOT operate
a vehicle if you are drowsy. During extended periods
of vehicle operation, you should take frequent breaks.
ImproperrelianceontheStayAlertfeaturemayresultin
vehicledamage,personalinjuryordeath.
OPERATIONOPERATION
Windshield
Mounting
Rubber
Bumper
4
5
3
•RadarSignatureID(RSID)
•LaserSignatureID(LSID)
•3FilterModes
•KaMaxMode
•TotalBandProtection
™
•OLEDTextDisplay
•DetectsPOP
™
Mode
•360°MaxxCoverage
•RealVoice
®
•3CityModes/HighwayMode
•Quiet/Auto Quiet Mode
•Dim/DarkMode
•AutoDim
•StayAlert
™
•SettingSaver
•
SelectableVehicleBatterySaver
™
•SafetyWarningSystem
™
•AlertPriority
•AlertPeriscopes
•TrafficFlowSignalRejection
Features
IMPORTANT: Unscrewslowly.Thetipcontains
a spring which may fly out when disassembling.
Insert the new fuse with the spring and screw on
the tip. With use, the screw cap on the plug may
loosen.Retightenitoccasionally.
Installing the Hardwire Kit
The“U”typeconnectormustbesecuredto
a metal surface that is electrically connected
to the battery ground (negative) terminal.The
spade type connector can connect to either live
12voltsorswitched12voltsatyourfusepanel
accessory port. If no port is available, cut off the
spadeterminal,expose1/4to1/2inchofwire,
andspliceintoasourceof12voltpower.
Fuse Replacement - Hardwire Kit
The inline fuse holder on the power cable is
equippedwithareplaceable2amp,3AGfuse
located inside the fuse holder.
To replace the fuse, carefully twist the holder to
open it to gain access to the fuse.
Integrated Real Voice
®
Whenselected,RealVoice
®
will be used to
articulatethefollowing:
 1. BandIdentification
 2. SafetyWarningSystemmessages
 3. FeatureSelection
Note: In certain cases, the voice message does
not replicate the text message.
Teach/Tutorial Mode
Provides simulated alerts for each type of signal.
•PressCityandQuietbuttonssimultaneously
•DisplayShows:
•PressDarkbuttontoexit.
Setting Saver
SettingSaverstoresyourpersonalizedsettings
so that when the detector is turned off and then
on again, you do not have to re-enter them.
Feature Engaged Confirmation
Each time a button is pressed, one beep
confirms feature “on”, two beeps confirm
feature “off”.
Auto Dim
The Auto Dim feature automatically switches the
illumination of the text display between the
bright and dim settings according to varying
light conditions so that the text display will
always be easy to read. To manually override
the auto dim feature, use the dark button on
theunit.EnterOptionSelectModetoturnoff
the auto dim feature.
2
9
6
1
8
10
11
7
13
12
14
Feature Display
Shows
To Change:
D=Dark
Q=Quiet
Option
QUIET
S1: Quiet
D or Q
to select
Remote Control of Dim, City,
Quiet Power Functions
POWER
S2: Power
D or Q
to select
Remote Control of Dim, City,
Quiet Power Functions
AUTO
DIM
ADIM:ON
D = ON
Q = OFF
Auto Dim On
Auto Dim Off
TONE TONE 3
D or Q
to select
Tone 1, 2, 3
(3 Different Tone Patterns)
TEST
TEST
ON
D = ON
Q = OFF
ON = X, K, Ka Audio Tones
OFF = One Beep During Power Up
X
BAND
X = ON
D = ON
Q = OFF
X Band ON
X Band OFF
K
BAND
K = ON
D = ON
Q = OFF
K Band ON
K Band OFF
Ka
BAND
Ka-
MAXID
D or Q
to select
Ka Band (RSID,NORM,
OFF,MAX,MAXID)
LASER
LSR
NORM
D or Q
to select
LASER
(NORM,OFF,LSID)
LASER
AREA 1
.02-.09 Y
D or Q
to select
Laser Area 1 ON
Laser Area 1 OFF
LASER
AREA 2
2.6-3.2 Y
D or Q
to select
Laser Area 2 ON
Laser Area 2 OFF
LASER
AREA 3
3.8-4.2 Y
D or Q
to select
Laser Area 3 ON
Laser Area 3 OFF
SWS
™
SWS
OFF
D = ON
Q = OFF
Turn SWS
™
ON
Turn SWS
™
OFF
VOICE
®
VOICE
ON
D = ON
Q = OFF
Real VOICE
®
Engaged
Real VOICE
®
Disengaged
POP
™
POP
OFF
D = ON
Q = OFF
POP ON
POP OFF
BATTERY
SAVER
B SVR
ON
D = ON
Q = OFF
Battery Saver ON
Battery Saver OFF
XK
FILTER
XK FLTR 1
D or Q
to select
Filter 1, Filter 2, Filter 3
Ka
FILTER
Ka FLTR 1
D or Q
to select
Filter 1, Filter 2, Filter 3
ALERT
PERISCOPES
LEDBLNK
D or Q
to select
Alert Periscopes ON
(ON, OFF or Blinking)
TFSR
TFSR
OFF
D = ON
Q = OFF
TFSR = ON
TFSR = OFF (default)
Option Select Mode
(cont’d)
NOTE:
Press and hold Menu button to exit Option
SelectMode.
NEVER OPERATE A
VEHICLE IF YOU
ARE DROWSY!
OWNER’S MANUAL
CR85
HIGH Performance
LASER-RADAR
DETECTOR