Filter
Top Products
1
ADDITIONAL WARNINGS!
Congratulations! The Roval wheelset you have chosen is among the
finest of advanced composite products available in cycling. Carbon
fiber is a very special material that requires particular care during
assembly, storage and riding. This short form installation guide contains
instructions and warnings, plus maintenance information.
Warning! Bicycle assembly is a complicated task requiring
training and experience, which should only be carried out by
a trained and experienced bicycle mechanic. Do not attempt
installation of any component if you do not have experience and
training as a bicycle mechanic.
• Ensure that the quick-releases are securely fastened, and that
the axles are centered within the dropouts.
• Inspect the rims and tires for any signs of excessive wear.
• Inspect the tires to ensure correct tire pressure and that the
beads are properly seated within the rim.
• Ensure that the wheels spin true and smooth with no side-to-
side play, and spoke tension is even on all spokes. There should
be no contact between the rim and the brake pad.
• Inspect the spokes for any signs of damage.
• Inspect the brakes for any signs of cable damage, excessive
brake pad wear or misalignment.
WARNING!
• Do not exceed tire’s maximum pressure rating, and do not
exceed 120 psi (8.3 bars).
• Do not under inflate tires. Under inflation may allow
contact between the rim and the road surface.
• Do not use tires narrower than 22mm. Tires narrower than
22mm may not protect the rim adequately from impacts.
WARNING! Do not use pads previously used on aluminum
rims. Alloy particles may be embedded into the pads, which
will damage the carbon surface. Always use a clean set of
pads when installing the Roval wheels.
IMPORTANT! Most brake pads for carbon rims have grooves or wear
indicators to show you how much life your pads have left. It’s very
important to replace the brake shoes when they are worn to the
bottom of the indicators.
• Refer to the installation procedures
recommended by the component
manufacturer.
• Ensure that the pads are properly
positioned and aligned.
• Ensure that the pads do not touch
the rims when the wheel is rotating.
When correctly positioned, the brake
pads should be 1mm away from the
braking surface of the rim. The pads
should be positioned 1 to 2mm below the
outer edge of the rim to prevent contact with the tire (fig.1)..
1-2mm
1mm
Fig.1
Please read the following Warnings. Because the failure to follow any
Warning may result in a catastrophic failure of the wheels, resulting in
serious personal injury or death, this phrase may not be repeated in
connection with each Warning.
WARNING! Only use brake pads recommended by Roval:
• Roval pads for carbon rims
• Swissstop Yellow King pads for carbon rims
• Kool Stop pads for carbon rims (charcoal colored)
Not all brands of pads are recommended. Use of other
manufacturer’s pads will void the warranty. Call customer
service for updates on authorization of different pads.
WARNING! Use proper braking techniques. The front brake
possesses most of the stopping power and should be used ac-
cordingly. Excessive or exclusive use of the rear brake to con-
trol speed on long descents is not recommended. Prolonged,
continuous use of brakes can build up excessive heat, which
may result in failure of rim, tire and/or tube.
BRAKE PAD REPLACEMENT
WARRANTY
For the complete warranty provisions, please refer to the
Specialized Owner’s Manual or www.specialized.com.
Periodically review the tech support section at www.specialized.
com for updates and additional technical information regarding this
product.
• Do not make any modifications to the wheels. To do so will void the
warranty and may cause failure.
• Ensure that the rim’s braking surface is kept clean. Grease, oil
and other contaminants can affect braking performance.
• Do not ride on components that have been damaged in an accident
or have worn beyond their usable limit. ALWAYS HAVE DAMAGED
OR WORN PARTS REPLACED BEFORE YOUR NEXT RIDE.
• Many different factors can affect the life span of Roval Wheels.
Adverse environmental conditions, impacts, falls, and road hazards
may compromise the structural integrity of the wheels and
significantly reduce their lifespan. Wheels and related components
are subject to wear over time. It is important to have your wheels
regularly inspected by a qualified mechanic for damage, fatigue, or
signs of wear. If the inspection finds any signs of damage (cracks,
stress marks, deformations), fatigue or wear immediately replace
the wheel or affected part.
• Great care should be taken to not damage the rim’s carbon fiber or
composite materials. Any damage may result in a loss of structural
integrity, which may result in a catastrophic failure. This damage may
or may not be visible in inspection. Before each ride, and after any
crash, you should carefully inspect your wheels for any dents, fray-
ing, gouging, scratches through the paint, chipping, bending, or any
other signs of damage. Do not ride if your wheels show any of these
signs. After any crash, and before you ride any further, take your
bicycle to an authorized Roval retailer for a complete inspection.
SPECIALIZED BICYCLE COMPONENTS
15130 Concord Circle, Morgan Hill, CA 95037 (408) 779-6229
Please note all instructions are subject to change for improvement without notice.
Rev.3, September 2006
• For all repair requirements, the wheels must be sent to the Roval Service
center, through your authorized Roval dealer.
• Roval wheels should be regularly inspected by a qualified bicycle
technician at an authorized Roval dealer, or by the Roval Service Center.
Regular maintenance is essential for maximum service life of the wheel.
• Always use a wheel bag for storage or transportation to prevent damage.
Prolonged exposure to sunlight can cause the carbon to yellow over time.
• Use only mild soap and water to clean the wheels. Do not use solvents or
harsh chemicals.
• Avoid direct contact with pressurized water on the hub to prevent
bearing or freehub damage.
Refer to following pages for hub maintenance steps.
• Roval composite rims are made to be lightweight, and are not suitable
for all riders and all possible uses. If the rider is approaching 250
pounds in weight (i.e., 240 pounds, etc.), Specialized recommends
against use of this wheel. Failure to follow this warning may result in a
catastrophic failure of the wheel, causing serious personal injury or death.
THIS BRIEF INSTALLATION GUIDE CONTAINS IMPORTANT INFORMATION.
PLEASE READ CAREFULLY AND STORE IN A SAFE PLACE.
ROVAL RAPIDE WHEELSET OWNER’S GUIDE
BRAKE PAD INSTALLATION
BEFORE EVERY RIDE:
GENERAL MAINTENANCE