Filter
Top Products
M6189-0920 Size: 8.5” x 11” Color: 1C + 1C
Please keep these instructions for future reference as they contain important information.
™™
®
3+
Asst. M0036
M6189-0920
Mattel, Inc., 333 Continental Blvd., El Segundo, CA 90245 U.S.A. Consumer Relations 1 (800) 524-8697
service.mattel.com. • Mattel Canada Inc., Mississauga, Ontario L5R 3W2. You may call us free at 1-800-524-8697.
• Mattel U.K. Ltd., Vanwall Business Park, Maidenhead SL6 4UB.
Helpline 01628500303 • Mattel Australia Pty.,
Ltd., Richmond, Victoria. 3121.Consumer Advisory Service - 1300 135 312. • Mattel East Asia Ltd., Room 1106,
South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. • Diimport & Diedarkan Oleh: Mattel
SEA Ptd Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410
PJ. Tel:03-78803817, Fax:03-78803867.
© 2007 Mattel, Inc. All Rights Reserved.
INSTRUCTIONS
Bumper Busters
Bumper Busters
™
Bumper Busters
™
CONTENTS
BATTERY INSTALLATION / REPLACEMENT
TO PLAY
1.
RESET
2.
RECYCLE INFORMATION (USA ONLY)
Please recycle button cell battery(ies) contained in this product by:
• Visiting your nearest recycling center. For location of the nearest recycling center, visit us online at
www.service.mattel.com.
• If a recycling center is not available in your area, contact us for a pre-paid mailing label.
Visit us online at www.service.mattel.com or call toll-free at 1-800-524-8697.
• Valid in the US only.
• Unscrew the battery cover with a Phillips
head screwdriver (not included).
• Remove batteries included for
demonstration purposes and dispose of
them safely. Install 3 new button-cell
(AG13, LR44) batteries in the orientation
(+/-) shown. For best performance, use
only alkaline batteries.
• Replace battery cover and tighten screw.
• Replace the batteries if the sounds are
garbled.
BATTERY SAFETY INFORMATION
In exceptional circumstances batteries may leak fluids that
can cause a chemical burn injury or ruin your product.
To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product
before being charged (if designed to be removable).
• Rechargeable batteries are only to be charged under adult
supervision (if designed to be removable).
• Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel-cadmium) batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as
recommended are to be used.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire.
The batteries inside may explode or leak.
Protect the environment by not disposing
of this product with household waste [2002/96/EC].
Check your local authority
for recycling advice and facilities.
Requires 3 button cell (AG13, LR44) batteries.
Batteries included are for demonstration purposes.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE:
Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user’s authority to operate the equipment.