Escort S2 Radar Detector User Manual


 
EZ-Programming
There are 10 user-selectable options so you can
customize your Solo S2 for your own preferences. The
Mode button (“M”) and the “VOL” buttons (up or
down arrows) are used to enter the programming,
REVIEW your current program settings, and to
CHANGE any settings as desired. The letters “PGM”
(program), RVW (review), and CHG (change) are
located on the front of the detector, and are high-
lighted in blue graphics. Pages 16-19 explain each
option in more detail.
How to use EZ-Programming
1 To enter Program Mode, press and hold either
of the “VOL” (up or down) buttons, and the “M”
(mode) down for 2 seconds. The unit will beep
twice, and will display the word “Program.”
2 Then press the RVW button to review the
current settings. You can either tap the button to
change from item to item, or press and hold the
button to scroll through the items.
3 Press the CHG button to change any setting.
You can either tap the button to change from
setting to setting, or hold the button to scroll
through all the options.
4 To leave the Program Mode, simply wait 8
seconds without pressing any button. The unit will
display Complete, beep 4 times, and return to
normal operation.
14
To quickly reset Solo S2 to the factory program
settings, press and hold the Mute and M (Mode)
buttons while turning Solo S2 on.
Example of EZ-Programming
Here is how you would turn Solo S2’s AutoMute
feature off.
1 Enter the Program Mode by holding one of the
VOL buttons and “M” (mode) button down for 2
seconds. Solo S2 will beep twice and display
“Program.”
2 Then hold the RVW button down. Solo S2 will
scroll through the categories, starting with Contrast,
Pilot options, Auto-Power, Power-On sequence,
Signal Strength Meter, AutoMute, Tones, City
sensitivity, Brightness, and Bands.
3 Release the RVW button when Solo S2 shows the
AutoMute item. Since the factory setting is for
AutoMute to be on, Solo S2 will display “aMute
ON.” (If you accidentally go to the next category,
press the opposite “VOL” button to go back.)
4 Press the CHG button to change from “aMuteON”
to “aMuteOFF.”
5 To complete the Programming, simply wait 8
seconds without pressing any button. Solo S2 will
display Complete, beep 4 times, and return to
normal operation.
Overview of EZ-Programming
15
Press the RVW button to go Press the CHG button to change
your setting within a category from one category to the next
CONTRAST
Contr 3 *Contrast level 3
Scrolls thru five contrast levels:1-5
PILOT LIGHT Pilot HWY *Full word:Highway or Auto or City
(Options using Pilot H Letter:H or A or C
12-volt SmartCord) Pilot H.> Letter,with scanning dot
Pilot + Symbol:+ or
or --
Pilot +.> Symbol,with scanning dot
Pilot +> Scanning symbol
AUTO POWER aPwr ON *Turns Solo S2 on and off automatically
aPwr OFF Turn Solo S2 on and off manually
POWER-ON SEQUENCE PwrOn STD *Standard power-on sequence
PwrOn FST Fast power-on sequence
SIGNAL STRENGTH METER Meter STD *Standard signal strength meter
Meter EXP Expert Meter
AUTOMUTE aMute ON *AutoMute on
aMute OFF AutoMute off
AUDIOTONES Tone STD *Standard tones
Tone LOUD Loud tones
CITY MODE SENSITIVITY City STD *Standard City mode sensitivity
City LoX Low X-band sensitivity in City Mode
City NoX No X-band sensitivity in City Mode
BRIGHTNESS Brt AUTO *Brightness is controlled automatically
Brt MIN Minimum brightness when turned on
Brt MED Medium brightness when turned on
Brt MAX Maximum brightness when turned on
Brt DARK Full Dark Mode when turned on
BANDS Bands ALL *All bands enabled
Bands MOD One or more bands are disabled
Turn bands “ON” or “OFF” by
pressing the Mute button
XONorOFF *X-band detection on
KONorOFF *K-band detection on
Ka ON orOFF *Ka-band detection on
LSR ON orOFF *Laser detection on
SWS ON orOFF *
SWS detection off
VG2 ON orOFF *VG2 detection off
*Solo S2’s Factory Settings
To reset Solo S2 to its original factory
settings, press and hold the Mute and
M (Mode) buttons while turning Solo S2
on. Solo S2’s display will provide a
“Reset” message, accompanied by an
audible alert, acknowledging the reset.