Conair HC221 Hair Clippers User Manual


 
Instructions for Care and Use
MODEL HC221
®
Pro-Style Haircut Kit
with Self-sharpening Stainless Blades
I
MPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially when
children are present, basic safety precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER any appliance is electri-
cally live, even when the switch is off.
To reduce the risk of death or injury by electric
shock:
1. Unplug this appliance before cleaning.
2. Do not place or store appliance where it can fall
or be pulled into a tub or sink.
3. Do not use while bathing or in a shower.
4. Do not place in, or drop into, water or other
liquid.
5. Do not reach for an appliance that has fallen
into water. Unplug immediately.
6. Always unplug this appliance from electrical
outlet immediately after using.
DO NOT REACH
INTO THE WATER
WARNING To reduce risk of burns,
electrocution, fire, or injury to persons:
1. This appliance should never be left unattended
when plugged in. Do not pull, twist, or wrap line
cord around appliance.
2. This appliance should not be used by, on, or near
children or individuals with certain disabilities.
3. Use this appliance only for its intended purpose
as described in this manual. Do not use attach-
ments not recommended by the manufacturer. Do
not use an extension cord to operate this appli-
ance.
4. Never operate appliance if it has a damaged
cord or plug, or if it is not working properly, if it
has been dropped or damaged, or dropped into
water. Return appliance to a service center for
examination and repair.
5. Keep cord away from heated surfaces.
6. Never drop or insert any object into any opening
on this appliance.
7. Do not place appliance on any surface while it
is operating.
8. Do not use this appliance with a
damaged or
broken comb or with teeth missing from the blades,
as injury may occur. Before use, make certain blades
are aligned properly. (See “Care of your Clippers.”)
9. Do not operate outdoors or where aerosol
(spray) products are being used or oxygen is being
administered.
10. Never operate the appliance with the air open-
ings blocked or while on a soft surface, such as
a bed or couch, where the air openings may be
blocked. Keep the air openings free of lint, hair,
and the like.
11. Always attach plug to appliance first, then to
outlet. To disconnect, turn all controls to “OFF”;
remove plug from outlet.
12. Avoid skin contact with moving blades.
13. Check for tangles or kinks in the cord. If the
cord does become tangled during use, turn unit off
and straighten cord before operating.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
This appliance is intended for household use.
Use on Alternating Current (120V AC 60Hz)
only. This appliance has a polarized plug (one
blade is wider than the other). As a safety
feature, this plug will fit in the outlet only one way.
If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electri-
cian. Do not attempt to defeat this safety feature.
Your new Conair Haircut Kit has everything you
need to achieve professional haircuts at home. Its
powerful high torque motor clipper, with high car-
bon stainless steel blades for long-lasting cutting
precision, features a new 5-position adjustamatic
taper control. Whatever hair length you set the
lever for, the clipper will automatically cut all hair
in that section at the desired length. Also included
are 9 attachment combs for different hair lengths
(including left and right ear taper combs), barber
scissors, a styling comb with angled teeth, a barber
comb with straight teeth, a full-length barber cape,
a case for easy storage, 3 styling clips to assist you
in cutting longer hair styles, a neck brush and a 28
minute step-by-step How-to DVD filled with styling
tips and techniques in both English and Spanish. It
also comes with lubricating oil, a cleaning brush
and a blade guard for easy maintenance and pro-
tection of the clipper blades.
THE CONAIR GUIDE
TO CUTTING HAIR AT HOME
Before you start:
1. Inspect your clipper. Make sure it’s free of hair
and dirt, properly oiled, and running smoothly.
2. Place cape around the neck of the person getting
a haircut.
3. Seat the person so that his or her head is at
your eye level.This gives you greater visibility
and control.
4. First, comb hair until it’s tangle-free. Then hold
clipper in a comfortable grip. Now you’re ready
to cut.
MEDIUM TO LONG CUT
To begin with, cut only a small amount
of hair until you become used to the length each
attachment leaves the hair. Try the longest attach-
ment comb and put the taper control in the high-
est setting. If you want a shorter cut, you can then
use shorter combs.
• Short attachment comb (number 1) cuts hair to 1/8".
Medium-Short attachment comb (number 2) cuts hair
to 1/4".
Medium-Long attachment comb (number 3) cuts hair
to 3/8".
• Long attachment comb (number 4) cuts hair to 1/2".
• Long attachment comb (number 5) cuts hair to 5/8".
• Long attachment comb (number 6) cuts hair to 3/4".
• Long attachment comb (number 7) cuts hair to 7/8".
• Left ear attachment comb lightly tapers over left ear.
• Right ear attachment comb lightly tapers over
right ear. These combs make this part of the
haircut easier.
Attach combs by hold-
ing them teeth up, then
snapping them onto the
bottom of the clipper
blade.
To remove comb attach-
ments, place index
finger and thumb as
illustrated; then pull out
and up.
NOTE: Never push or shove the clipper through
the hair to make it move more quickly.
Professional experience shows that the clipper
works most efficiently when it cuts through
the hair at its own speed.
To begin cutting hair:
1. The hair should be combed in its natural
direction.
2. Using the largest attachment comb, trim sides
from the bottom upward. Hold
clip per lightly against the hair
with teeth of the attachment
comb pointing up ward, yet flat
against the head.
Gradually lift the clip per
upward and outward through
the hair, trimming just a little at a time.
Repeat around sides and back of head.
If you want hair to be even
shorter:
A) Apply more pressure to
the head with the attach-
ment comb that is in place.
This takes a little practice,
of course.
OR
B) Just switch to a shorter
attachment comb.
Remember, it’s better to
leave too much hair than
too little. For longer hair
on top, use the barber
comb and lift hair on the
top of the head, cutting
over the comb, or hold the
hair between the fingers
and cut to desired length.
Always working from the
front to the back of the
head, gradually cut the
hair shorter by reducing
the space between the comb or fingers and the
head. Comb often to check for uneven strands,
and to get rid of trimmed hair.
OUTLINING
Outlining requires no attachments. Comb
hair into the desired style. Position the
clipper between the sideburns and the ear (see
below), making sure the corner edge of the
blade is against the hairline. With the outline of
the hair as your guide, slowly move the clipper
over, around and behind the ears. For the back
of the neck and the sideburns, hold the clipper
upside down (see above) and, holding it against
the skin at the length desired, move the clipper
downward.
STOP. COMB. CHECK.
For best results, do as the professionals do: comb
hair often, and check clipping results as you
comb. This way you avoid uneven sides, bangs,
neckline, etc.
SHORTCUTS TO PERFECT
FLAT TOPS, CREW CUTS, ETC.
Always cut from the back of the neck to the
crown, using the longest comb setting. Hold the
comb attachment flat against the head and slowly
move the clipper up through the hair. Use the
same technique for the sides, cutting from the
bottom to the upper side of the head.
For the front to the crown, cut the hair against
the direction in which it grows, then even it up
with the sides.
For a flat top, use the flat comb, not the attach-
ment comb. Just cut hair on top of the head over
flat comb (see above).
To taper hair down to the neckline, use attach-
ment comb #1. Comb hair and check for uneven
spots. Outline sideburns and neck areas (see
“Outlining”).
USER MAINTENANCE
CARE OF YOUR CLIPPERS
MAINTENANCE OF THE BLADE
This clipper comes with a removable blade set.
To remove the blades follow
these steps:
1. Hold the front part of the
clipper with your thumb
pressing on the blade and
place another hand against
the blade. (see fig. 1)
2. When pressing the
blade forward, the blade is
detached. (see fig. 2)
TO REPLACE BLADES:
1. Set the Taper Control
Button to lowest position
“1” (see fig. 3)
2. Place the blade onto the
clipper body by inserting
the “Blade Tongue” down
below the “Lock Tap”.
(see fig. 4)
3. Snap the blade down
into following position. The
blade is now fixed onto the
clipper body. (see fig. 5)
SPECIAL OIL
Always apply oil to the blades before, during or
after use. This will ensure maximum cutting per-
formance. Hold clipper away from your body in a
downward position and apply oil on the front and
sides of the cutter blade. Wipe excess oil off with
a soft, dry cloth.
To maintain the blades of your Conair
clipper, oil
them after every three or four haircuts. Gently
place a few drops of oil on the teeth of the blades,
using the special Conair
oil included with your set.
Turn the clipper on for
a minute, then turn
off. This light, natural
oil was formulated
specifically for the Conair high speed clipper.
Be cause it is the right oil to use, it will not slow
down the blades. Never use any other product.
There is no substitute for Conair oil.
Any other servicing should be performed by an
authorized service representative or that the
appliance has no user serviceable parts. The
product is for household use. Do not pull, twist, or
wrap line cord around appliance.
ADJUSTABLE 5 DETENT
TAPER CONTROL
The Conair taper control is positioned at the back
of the unit so you can hold the clipper in your
hand and adjust the lever at the same time...while
you’re clipping. This taper control eliminates the
need in some situations for an attachment comb,
because it lets you gradually adjust the closeness
of the cut. For the closest cut and the shortest hair,
push taper control up as far as it will go to level
#5. To increase cutting length, slowly push control
down. If you push to the lowest position level #1, it
will leave hair about the same length as the short
attachment comb.
Because a different cutting edge is used in each
setting, the taper lever lengthens the life of your
blades. Packed-in hair can slow down any clipper.
To remove it without removing the blades, take
your cleaning brush and brush the hair from the
blades. If you do this after every clipping, espe-
cially with heavy hair cutting, the blades should
remain free of cut hair. If clipper stops cutting and
this action doesn’t help, try loosening the blades
to remove the hair.
If clipper stops cutting, check to see if there
is a clump of hair lodged between the blades.
If that is the problem, unplug the clipper and
then loosen the blades to remove the hair.
This clipper has a detachable blade that
makes cleaning easy. Just push up on the
top of the blade and it will pop off easily.
Remove any loose hair with the cleaning
brush provided and then place blade back
in position. To secure properly, line up the
base of the blade with the lower back of the
clipper. Push down into place until you hear
a snap to know it’s locked in place.
If the clipper stops cutting but does not stop
running, you will need to check the blades.
For new blades, send check or money order for
$6.50 which includes postage and handling to:
Conair Corporation
150 Milford Rd.
East Windsor, NJ 08520
NOTE:
Never pull on the clipper cord. Never
twist or wrap the cord around the
clipper. To store your clipper, lay it flat with
the cord coiled up, then place in cylinder.
MEDIDAS DE SEGURIDAD
IMPORTANTES
Cuando se usan aparatos eléctricos, especial-
mente en la presencia de niños, siempre se deben
tomar precauciones básicas de seguridad, entre las
cuales las siguientes:
LEA TODAS LAS
INSTRUCCIONES ANTES DE
USARLO
MANTENGA EL APARATO
ALEJADO DEL AGUA
PELIGRO Cualquier electrodoméstico
permanece eléctricamente activo, incluso cuando el
interruptor está apagado. Para reducir el riesgo de
muerte o herida por descarga:
1. Desconecte el aparato antes de limpiarlo.
2. No coloque ni guarde el aparato donde pueda caer o
ser empujado a una bañera o un lavabo.
3. No lo use mientras se esté bañando o tomando una
ducha.
4. No coloque el aparato ni lo deje caer al agua u otro
líquido.
5. No intente de alcanzar un aparato que ha caído al
agua. Desenchúfelo inmediatamente.
6. Siempre desconecte el aparato inmediatamente
después de usarlo
NO TRATE DE ALCANZAR
EL APARATO EN EL AGUA
ADVERTENCIA Para reducir
el riesgo de quemaduras, electrocución, incendio
o lesiones personales:
1. Nunca deje este aparato desatendido mientras está
conectado. No jale, doble o enrolle el cable alrededor del
aparato.
2. Este aparato no debería ser usado por, sobre o cerca de
niños o personas con alguna discapacidad.
3. Use este aparato únicamente con el propósito para el
cual fue diseñado y tal como se describe en este manual.
Sólo use accesorios recomendados por el fabricante.
4. Nunca utilice el aparato si el cable o la clavija están
dañados, si no funciona correctamente, si ha caído, si está
dañado o si ha caído al agua. Llévelo a un centro de servicio
autorizado para que lo examinen y lo reparen.
5. Mantenga el cable alejado de superficies calientes.
6. Nunca deje caer ni inserte un objeto en ninguna de las
aberturas.
7. No coloque el aparato en ninguna superficie mientras
está funcionando.
8. No use este aparato con un peine accesorio roto o
lastimado o si le faltan dientes a la cuchilla. Esto podría
provocar una herida. Asegúrese que las cuchillas estén
correctamente alineadas antes de usarlo (véase la sección
“Instrucciones de mantenimiento”).
9. No utilice este aparato al aire libre, ni donde se están
usando productos en aerosol (spray) o donde se está
administrando oxígeno.
10. Nunca bloquee las aberturas de aire o coloque el
aparato en una superficie blanda, como una cama o un sofá,
donde se puedan obstruir. Mantenga las aberturas libres de
pelusas, cabellos y elementos similares.
11. Siempre conecte el cable al aparato antes de conec-
tarlo a la toma de corriente. Para desconectarlo, coloque
todos los ajustes en la posición “Apagado” (OFF), luego
desenchufe el cable.
12. Evite que las cuchillas toquen la piel cuando están
moviendo.
13.Siempre asegúrese que el cable del aparato no esté
enredado. Si el cable se enreda o se enrolla mientras está
usando el aparato, apáguelo inmediatamente y enderece el
cable antes de volverlo a usar.
GUARDE ESTAS
INSTRUCCIONES
INSTRUCCIONES
DE USO
Este aparato fue diseñado para uso doméstico.
Úselo con Corriente Alterna de 120V (60 hertzios)
únicamente. Este aparato tiene una clavija polarizada
(un polo es más ancho que otro). Como medida de
seguridad, se podrá enchufar de una sola manera
en la toma de corriente polarizada. Si no entra por
completo, inviértela. Si aún no entra completamente,
llame a un electricista calificado. No intente vencer
esta función de seguridad.
Su conjunto de peluquería de Conair® tiene todo
lo que usted necesita para lograr cortes de cabello
profesionales en su casa. Incluye una cortadora para
el cabello con un potente motor de rotación rápida,
un botón de ajuste de recorte con 5 posiciones
y cuchillas de acero inoxidable duro para un cortado
preciso. También incluye 9 peines accesorios para
lograr distintos largos de recorte (incluso un peine
para la oreja izquierda y un peine para la oreja
derecha), tijeras de peluquero, un peine de
modelado con dientes ladeadas, un peine de
peluquero con dientes rectas, una capa de
peluquero, una caja de almacenamiento, 3 clips
para el cabello más largo, aceite lubricante, un
cepillo de limpieza, un cepillo para el cuelo, y
una cubierta protectora. Por fin, incluye un DVD
educativo de 28 minutos en inglés y en español.
GUÍA DE CONAIR PARA CORTAR
EL CABELLO EN SU CASA
Antes de empezar:
1. Inspeccione el aparato para asegurarse que
esté libre de cabello y polvo, que esté lubricado y
que funcione correctamente
2. Coloque una toalla o una capa de barbero
alrededor del cuello de la persona a quien le va a
cortar el cabello
3. Siente a la persona de manera que su cabeza
esté al nivel de sus ojos para mayor visibilidad y
control
4. Desenrede el cabello, luego coja la cortadora
confortablemente en su mano. Ya está listo para
empezar.
CORTES MEDIANOS A LARGOS
Empiece por cortar poco cabello, hasta acostum-
brase al cortado de cada peine accesorio. Use el
peine accesorio más largo para empezar, luego
use peines accesorios más cortos para acortar
el cabello.
• El peine accesorio corto (No.1) corta el cabello a 1/8”
(3mm)
• El peine accesorio mediano-corto (No.2) corta el cabello a
1/4” (6mm)
• El peine accesorio mediano-largo (No.3) corta el cabello a
3/8” (9mm)
• El peine accesorio largo (No.4) corta el cabello a 1/2”
(13mm)
• El peine accesorio largo (No.5) corta el cabello a 5/8”
(16mm)
• El peine accesorio largo (No.6) corta el cabello a 3/4”
(19mm)
• El peine accesorio largo (No.7) corta el cabello a 7/8”
(22mm)
• El peine accesorio para la oreja izquierda contornea la
oreja izquierda
• El peine accesorio para la oreja derecha contornea la oreja
derecha
Para ensamblar el
peine accesorio, sos-
téngalo cabeza arriba y
engánchelo en la parte
inferior del filo de la cor-
tadora.
Para quitar el peine
accesorio, cójalo entre
los dedos índice y pul-
gar, tal como se ve en
la ilustración, y jale el
peine hacia arriba y
afuera.
NOTA: Nunca empuje la cortadora para que
corte más rápidamente. La experiencia profe-
sional demuestra que funciona mejor cuando
corta a su propia velocidad.
Empezar el corte de cabello:
1. Peine el cabello en la dirección de su creci-
miento natural.
2. Empiece el recorte a un lado de la cabeza,
usando el peine accesorio
más largo, y cortando de abajo
hacia arriba. Sostenga la cor-
tadora ligeramente contra el
cabello con los dientes del
peine apuntando hacia arriba
y plano contra la cabeza. Pase
la cortadora en el cabello gradualmente hacia
arriba y hacia fuera, cortando un poco cada vez.
Repita al otro lado y atrás
de la cabeza.
Si quiere un corte de
cabello aún más corto:
A) Aplique más presión
con el peine accesorio.
Esto necesita al principio
un poco de práctica.
O
B) Cambie el peine
accesorio por uno más
corto. Recuérdese que es
mejor dejar demasiado
cabello que muy poco.
Si quiere dejar el cabello
más largo encima de
la cabeza, use el peine
de barbero o sus dedos
para levantar el cabello y
corte a lo largo deseado.
Trabaje siempre de adel-
ante por atrás de la cabeza y corte el cabello poco
a poco, reduciendo el espacio entre sus dedos o
el peine y la cabeza. Peine con frecuencia para
verificar que no haya mechones disparejos y para
eliminar el cabello cortado.
CONTORNEO
El contorneo no requiere accesorios. Peine
el cabello en el estilo deseado. Coloque la
cortadora entre las patillas y la oreja (véase
el dibujo) y asegúrese que la esquina de la
cuchilla se encuentre contra el nacimiento
del pelo. Mueva la cortadora lentamente
sobre, alrededor y por atrás de las orejas,
siguiendo la forma del cabello. Para cortar
el pelo en la nuca y las patillas, sosten-
ga la cortadora al revés (véase el dibujo),
colóquela contra la piel al nivel deseado y
muévala hacia abajo.
DETÉNGASE. PEINE. VERIFIQUE
Para resultados óptimos, siga el ejemplo de los
profesionales: peine el cabello con frecuencia
y verifique los resultados mientras peine. Esto
evitará tener lados, flequillos o líneas de nuca
disparejos.
PERFECTOS CORTES CON
CORONILLAS PLANAS, CORTES
MILITARES ETC.
Siempre corte el cabello desde la parte trasera
de la nuca hacia la coronilla, usando el peine
accesorio más largo. Sostenga el peine contra
la cabeza y mueva la cortadora lentamente en el
cabello hacia arriba. Use la misma técnica para
los lados, cortando desde abajo hasta la parte
superior lateral de la cabeza.
Para la parte delantera, corte el cabello en la
dirección contraria a la del crecimiento natural del
cabello, luego iguale los lados.
Para una coronilla plana, use un peine plano en
vez de un peine accesorio, y corte el cabello
encima del peine (véase el dibujo).
Para cortar el pelo en la nuca y en las patillas,
use el peine accesorio No.1 (Véase la sección
“Contorneo”).
INSTRUCCIONES DE
MANTENIMIENTO
CORTADORA PARA EL CABELLO
JUEGO DE CUCHILLAS AMOVIBLES
El aparato incluye un juego de cuchillas amovible.
Siga las instrucciones siguientes para sacar las
cuchillas:
PARA SACAR LAS CUCHILLAS
1. Sostenga la cortadora
con el botón de encendido/
apagado frente suyo. Ponga
una mano debajo de las
cuchillas y empuje las mismas
con el pulgar de la otra mano
(Fig.1)
2. Empuje las cuchillas hacia
delante hasta desencajarlas
(Fig.2)
PARA INSTALAR LAS
CUCHILLAS
1. Ponga la palanca regula-
dora en la posición más baja
“1” (Fig.3)
2. Inserte la lengüeta negra
del juego de cuchillas en la
hendidura de la cortadora
(Fig.4)
3. Apriete el juego de cuchillas
para sujetarlo (Fig.5)
ACEITE ESPECIAL
Para mantener las cuchillas de su cortadora en
condición óptima, lubríquelas después de tres o
cuatro cortes de cabello, aplicando unas cuantas
gotas de aceite lubricante en los dientes de las
cuchillas. Encienda
la cortadora durante
un minuto, luego
apáguela. El aceite
lubricante fue
específicamente diseñado para las cortadoras de
alta velocidad de Conair®. Porque es el aceite
adecuado, no reducirá la velocidad de las cuchillas.
Nunca use otro aceite para lubricar su aparato. No
hay ningún substituto al aceite de Conair.
BOTÓN DE AJUSTE DEL RECORTE
CON 5 POSICIONES
Su cortadora está equipada con un botón de ajuste
del recorte, ubicado en la parte trasera del aparato,
el cual le permite controlar lo largo del recorte a
medida que corta el cabello.
En algunos casos, el botón de ajuste del recorte le
permite cortar el cabello más corto o más largo, sin
necesidad de usar un peine accesorio. Para un corte
más corto, mueva el botón hacia arriba. El nivel más
corto es el nivel 1. Para un corte más largo, mueva
el botón lentamente hacia abajo. El nivel más largo
es el nivel 5. El ajuste más largo dejará el cabello tan
corto como el peine accesorio corto No.1.
Usar el botón de ajuste del recorte prolonga la
vida útil de las cuchillas, puesto que nunca usan
el mismo ángulo para cortar. Su cortadora puede
perder velocidad si recortes de cabello están
trabados en las cuchillas. Para limpiarlas sin tener
que removerlas, use el cepillo de limpieza provisto.
Hacer esto después de cada uso, especialmente
cuando se corta mucho cabello, mantendrá las
cuchillas en condición óptima. Si la cortadora deja
de funcionar, y que esto no soluciona el problema,
desenchúfela y afloje las cuchillas para limpiarlas.
Si la cortadora deja de cortar, pero sigue funcio-
nando, inspeccione las cuchillas. Cámbielas si
están embotadas. Puede pedir nuevas cuchillas
por correo, mandando un cheque o un giro postal
de $6,50US (incluye gastos de envío y manejo) a la
dirección más abajo.
Conair Corporation
150 Milford Rd.
East Windsor, NJ 08520
Nota: Nunca jale, tuerce o enrolle el cable
alrededor del aparato. Cuando no use el
aparato, deje el cable libre al lado del
aparato y guarde el aparato sobre una
superficie plana o adentro del cilindro de
almacenamiento previsto.
Instrucciones de uso y de mantenimiento
MODELO HC221
®
Conjunto de Peluquería
con cuchillas de acero
inoxidable con autoafi lado