Filter
Top Products
Table of user-selectable features: 1 chirp = OFF, two chirps = ON.
Feature Select
Column 1
1st latched
Column 2
2nd latched
Column 3
3rd latched
Row 1
1st momentary
Add new remote to channel 1
info on page 11 NOTE 1
AutoLock on/off
info on page 16
Enhanced AutoArming: on/off
info on page 13
Row 2
2nd momentary
Add new remote to channel 2
info on page 11 NOTE 2
AutoUnLock on/off
info on page 16
AutoArm & Lock: on/off
info on page 13
Row 3
3rd momentary
Add new remote to channel 3
info on page 11 NOTE 3
FACT: on/off
info on page 16
✱ Set headlight duration: 1sec - 2.5min (30sec)
info on page 12 NOTE 6
Row 4
4th momentary
Add new remote to channel 4
info on page 11 NOTE 4
AutoActivate timed accessory upon remote arming: on/off
THIS FEATURE IS FOR INSTALLERS ONLY
Siren duration: 60/30 seconds
(1/2 chirps) info on page 19
Row 5
5th momentary
Erase all channels
info on page 22 NOTE 5
Long-term chirp silencing: on/off
info on page 19
Set a new secret valet code
info on page 15 NOTE 7
✱ WARNING: If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING: it requires installer-only adjustment. Changing the duration may cause damage.
Please Note: There is a column 4 that contains installer-only features; do not change any of these settings. If you accidentally select column 4, turn off the ignition.
NOTE 1: Transmit channel 1 (or other channel of your choosing) of the new
remote control. You will hear one chirp to confirm programming of channel 1.
NOTE 2: Transmit channel 2 (or other channel of your choosing) of the new
remote control. You will hear two chirps to confirm programming of channel 2.
NOTE 3: Transmit channel 3 (or other channel of your choosing) of the new
remote control. You will hear three chirps to confirm programming of channel 3.
NOTE 4: Transmit channel 4 (or other channel of your choosing) of the new
remote control. You will hear four chirps to confirm programming of channel 4.
NOTE 5: When you hear one chirp, all remotes will have been erased from the
system memory. You must now add the new and/or existing remote controls to
the system (i.e., program channels 1–4 of each remote that will be used with
your Concept 20).
NOTE 6: The headlight timer starts as soon as you select this feature. When the
duration you wish has been reached, press button 1 on the remote control. You
will hear two chirps to confirm the new headlight timer duration.
NOTE 7:
Immediately flip the switch to its latched position
, then:
a. Enter the new code that you wish to use. The system will sound the same
number of chirps as the digit you choose when you move the switch to the
latched side (e.g., if the first digit is 4, you’ll hear four chirps when you
press the latched side).
b. Make sure to return the switch to its center position when complete.
c. Wait 3 seconds until you hear 2 chirps, indicating the new code has been
accepted.
d. Turn the ignition off. You’ll hear 3 chirps to confirm program mode exit
and the LED will turn off.
e. VERY IMPORTANT: You must immediately test your new secret
disarming/valet code
: Turn the ignition on, enter your new code, then flip
the switch to its latched position. The LED will illuminate. If it does not,
the new code you programmed and the one you just entered do not match.
The system has reverted to the previous code.
23 24
© Copyright Clifford Electronics, Inc., 1994