Filter
Top Products
Ta ble of user- selectable fea tures: 1 chirp = OFF, two chirps = ON.
Fea ture Se lect
Col umn 1
1st latched
Col umn 2
2nd latched
Col umn 3
3rd latched
Row 1
1st mo men tary
Add new re mote to chan nel 1
info on page 11 NOTE 1
AutoLock on/off
info on page 16
En hanced AutoArming: on/off
info on page 13
Row 2
2nd mo men tary
Add new re mote to chan nel 2
info on page 11 NOTE 2
Aut oUn Lock on/off
info on page 16
AutoArm & Lock: on/off
info on page 13
Row 3
3rd mo men tary
Add new re mote to chan nel 3
info on page 11 NOTE 3
FACT: on/off
info on page 16
✱ Set head light du ra tion: 1sec - 2min (30sec )
info on page 12 NOTE 6
Row 4
4th mo men tary
Add new re mote to chan nel 4
info on page 11 NOTE 4
AutoAc ti vate timed ac ces sory upon re mote arm ing: on/off
THIS FEA TURE IS FOR IN STALLERS ONLY
Si ren du ra tion: 60/30 sec onds
(1/2 chirps) info on page 19
Row 5
5th mo men tary
Erase all chan nels
info on page 22 NOTE 5
Long- term chirp si lenc ing: on/off
info on page 19
Set a new se cret valet code
info on page 15 NOTE 7
✱ WARN ING: If you have re mote win dow and sun roof clo sure, DO NOT CHANGE THIS SET TING: it re quires insta ller- only ad just ment. Chang ing the du ra tion may cause dam age.
Please Note: There is a col umn 4 that con tains installer- only fea tures; do not change any of th ese set tings. If you ac ci den tally se lect col umn 4, turn off the ig ni tion.
n NOTE 1: Transmit channel 1 (or other channel of your choosing) of the new
remote control. You will hear one chirp to confirm programming of channel 1.
n NOTE 2: Transmit channel 2 (or other channel of your choosing) of the new
remote control. You will hear two chirps to confirm programming of channel 2.
n NOTE 3: Transmit channel 3 (or other channel of your choosing) of the new
remote control. You will hear three chirps to confirm programming of channel 3.
n NOTE 4: Transmit channel 4 (or other channel of your choosing) of the new
remote control. You will hear four chirps to confirm programming of channel
4.
n NOTE 5: When you hear one chirp, all remotes will have been erased from the
system memory. You must now add the new and/or existing remote controls to
the system (i.e., program channels 1–4 of each remote that will be used with
your Concept 20).
n NOTE 6:The headlight timer starts as soon as you select this feature. When the
duration you wish has been reached, press button 1 on the remote control. You
will hear two chirps to confirm the new headlight timer duration.
n NOTE 7:Immediately flip the switch to its latched position , then:
a. Enter the new code that you wish to use. The system will sound the same
number of chirps as the digit you choose when you move the switch to the
latched side (e.g., if the first digit is 4, you’ll hear four chirps when you
press the latched side).
b. Make sure to return the switch to its center position when complete.
c.
Wait 3 seconds until you hear 2 chirps , indicating the new code has been
accepted.
d.Turn the ignition off. You’ll hear 3 chirps to confirm program mode exit
and the LED will turn off.
e.
VERY IMPORTANT: You must immediately test your new secret
disarming/valet code: Turn the ignition on, enter your new code, then flip
the switch to its latched position. The LED will illuminate. If it does not,
the new code you programmed and the one you just entered do not match.
The system has reverted to the previous code.
23 24
© Copyright Clifford Electronics, Inc., 1997 31-900A/Cy9OM/197