Filter
Top Products
Smart Au toTest ing™
Each time you remotely arm the system, it tests all triggers and sensors. If the hood or trunk is open, the system will immediately sound 4 chirps and 4
indicator light flashes instead of the usual 2 and 2. If a door is ajar, you’ll receive 2 chirps and 2 flashes, then, 5 seconds later, there will be 4 chirps and 4
flashes. If a sensor is malfunctioning, you will receive the usual 2 chirps and 2 flashes, then, 10 seconds later, there will be 4 chirps and 4 flashes.
NOTE: Since this is a warn ing in di ca tion, you will hear the 4 chirps even if you use the chirp mut ing fea ture.
n Specific malfunction identification: The system can also indicate the specific trigger or sensor that is malfunctioning. If you get the
4-chirp/4-flash signal upon arming, perform the following to identify the malfunctioning trigger or sensor:
1. Remotely disarm, then turn on the ignition. The LED status indicator inside your vehicle will be fl ashing, pause, then repeat.
2. Count the number of flashes in one cycle between pauses (for your convenience, the flash cycle repe ats a total of 5 times) and refer to the chart below:
LED flashes Meaning
1 flash
Activation of optional sensor
2 flashes
Activation of Piezo Sensor
4 flashes*
Door open/ajar
5 flashes
Trunk/hood open/ajar (trunk only if you have the IntelliStart 4 option)
6 flashes
Hood open/ajar (only if you have the IntelliStart 4 option)
7 flashes
Ignition switch was turned on while the system was armed
8 flashes
Three or more incorrect valet codes were entered
10 flashes
Power tampering or the vehicle battery is very low
* If your ve hi cle has a factory- installed fea ture that turns off or dims the in te rior cour te sy lights sev eral sec onds af ter you exit the ve hi cle, the sys tem can not pro vide this in di ca tion.
Auto matic mal func tion by pass with AutoRe Moni tor ing™
The system automatically bypasses any faulty point and arms all other triggers and sensors for the utmost possible protection. If you accidentally arm with
the hood, trunk or a door open, just close it (no need to disarm-and-rearm) and the system will again monitor that point.
Smart prior in tru sion at tempt alert
If you hear three chirps when you disarm, it means that a trigger or sensor was activated in your absence. When you turn on the ignition, the LED will flash 1-8
times, pause, then repeat the flash cycle 4 more times. Count the flashes in one cycle and refer to the chart above.
Multiple- event To tal Re call™
The system’s memory records the identity of the last eight activated or malfunctioning triggers and sensors, which allows your installer to instantly track down
malfunctions. To identify the triggers and sensors held in the system’s memory, use the following p rocedure:
1. Remotely arm and disarm while pressing the blank button on the PlainView 2 switch.
2. The LED will flash 1-10 times to indicate the most recently activated point, pause, flash 1-10 time s to indicate the second most recently activated
point, and so on.
3. Write down the number of flashes between pauses and refer to the chart above.
With the optional CliffNet Wizard, you’ll see this chronological report right on screen.
Smart Powe rUp™ 2
If power is removed, SmartPowerUp 2 ensures the system automatically restores itself to its previou s state when power is restored. So if a thief disconnects
the power and then restores it in an attempt to start the car, the system will re-arm and instantly sound the siren while continuing to immobilize the
starter. If your vehicle is to be serviced by a mechanic, just put the system in valet mode. If the mechanic needs to interrupt power, your system will
automatically return to its valet mode state when power is restored; there will be no alarm activat ion.
Op tional Cliff Net Wiz ard™ & Da ta Port In ter face Con nec tor
If you opted to have the Clifford DataPort interface connector installed with your system, you can use our CliffNet Wizard software to access your system
through your Windows PC. CliffNet Wizard will show you, on your PC screen, all your user-programmab le feature settings. You can change settings
simply by mouse-clicking the graphical button for each feature. You can customize features, add or delete remote controls, change remote control button
assignments, view a chronological history of trigger and sensor activations, and much more. It’s ac tually fun! And secure. To learn more and download
this free software, go to www.clifford.com/wizard .
7