Chrysler CHDL4JDL Automobile Alarm User Manual


 
Description: Chrysler Dodge Jeep Door Lock Alarm Interface (NO KEY REQUIRED)
Functions: Data Bus Interface: Lock/Unlock, Trunk/Rear Hatch, OEM Security Arm/Disarm, Starter Enable, Door Sense Trigger
Downloadable Firmware for Platform #03: CHDL7, ,CHDL6+,CHDL2, CHDL3, CHDL4 JDL
Brown
*Activation Input (See Note)*
INPUT
(-)
Black
Chassis Ground
INPUT
(-)
Orange
Trunk Input
INPUT
(-)
Blue
Unlock
INPUT
(-)
Green
Lock
INPUT
(-)
Pink
Start Input
INPUT
(+)
Pink/White
Door Sense Trigger
OUT
(-)
Violet/White
MUX (2nd Start) (See Wire Guide)
OUTPUT
(-)
Violet
DATA
Data
PC
.
.
Red
(+)12 Volt Constant
INPUT
(+)
Installation
Manual (1\2 Pages)
Platform #03 Firmware: CHDL7
“B” Requires ClearCode Vehicle Interface Protocol
See Wire Connection Guide for detailed information regarding wire functionality
Option A
Firmware Upgrades
USB Adaptor
USB Cable
Option B Data 2 Data connection with RCS
4 PIN DATA TO DATA (D2D) CABLE (OPTIONAL ACCESSORY)
Blue
B
r w
n
o
1
0
PI
N AR
N
E
H S
S
Section A
LED
DD
2
Programming
button
WIRE GUIDE: CONNECTIONS
Section B
“Fig. 1”
8
6
PI
N
1
87
87A
30
85
86
“Fig. 2”
Connect to
ignition (+)
of remote
starter
wire
Connect to Brown wire from bypass module.
Chassis Ground
GWR from
remote starter
i e
s i c p
t
V
w s o
DISCLAIMER
uThs Interface kit / Data Bus Interface part has been test d on the li ted vehicles. Other veh
cles will be added to the sele
t vehicle list upon com
letion of compaibility testing.
isit ebsite for late
t vehicle applicati
n guide. : Under no circ
mstances shall
r
s r
e
y
s
s e o m a
n
t w
the manufacturer or the dist
ibutor of the byp
ass kit / data bus inte
face part(s) be h ld liable for an
con equential damages su t
ain d in c
nnection with the p
art(s) inst
allation. The
anuf cturer a d it’s distribuors
ill
not, nor will they authorize any representative or
a t
i u
a
o
n
ny o
her ndivid
al to ssume bligation or liability in relation to the interface kit / data bus interface p
art(s) other than its replaceme t.
d
h d r
r u
N.B.:Un
er no circumstances shall t e manufacturer and
istributo
s of
this p od ct are liable for consequential damages sust
ained in
c
a
a i l
conne
tion with this product neither ssumes nor uthorizes any represent
ative or other person
to assume for it any obl
gation or
iability other than the replacement of this product only
.
*NOTE: If the remote control system
does not have an activation output
that turns on at exactly the same time
as the 1st ignition, then add relay and
install as per Fig.2. Most remote
systems GWR or (-) 3rd ign. outputs
turn on before the main ignition and
will cause diagnostic codes.
D
2D
RC SEMOTE ONTROL YSTEM
L
ES
S
/
S
T R
/
A AR
M
K
EY
A T
E
R L
R
CS
DATA
WIRE
SKIM
MODULE
WARNING: Before beginning your install go to www.XpressDownload.com and be sure to print the LATEST corresponding installation manual
for the firmware that is flashed to the platform you are using.
U
P
G
R
AD
E
A
BLE
O
R L
CK
DO
O
ERFACE
IN
T
M
D
U
L O E
U
P
G
R
AD
E
A
BLE
O
R L
CK
DO
O
ERFACE
IN
T
M
D
U
L O E
Internet
Legend RCS = Remote Control System N/C = No Connection N/A = Not Applicable W2W= analogue wire to wire D2D= data 2 data
(-)
/(+)
(-)
VEHICLE
TYPE
Input
Input
Input
Input
Input
Input
Input
Output
Output
Data
(-)
(-)
WIRE
COLOR
Brown
Green
Blue
Violet/
White
Violet
Pink/
White
Pink
Orange
Red
Black
(-)
(-)
(-)
(+)
SPECIFIC WIRE CONNECTION LOCATION
MUX (Violet/Brown Pin 4 of Ignition Harness)
Trunk Output
Constant (+) 12 Volt Source
Chassis Ground
Connect
Location
Vehicle
RCS
RCS
RCS
RCS
Vehicle
Vehicle
Vehicle
(-)
ACTIVATION and/or FUNCTIONALITY
Factory Alarm Arm/ Disarm
Lock All Doors
Unlock All Doors (See User Settings)
2nd Start and Accessory (Resistance)
Output to Vehicle
Enables 2nd Start
Trunk/Rear Hatch Release
RCS
Start Output - Connection is parallel to the vehicle and remote
control system starter wires.
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
(See Fig. 1)
(+)
RCS
Power Source
Ground Source
I/O
STATUS
PIN#
1
2
3
4
5
6
7
8
9
10
D2D
VIP
D2D
D2D
D2D
D2D
D2D
D2D
Detects Doors status (open/closed) via data
bus then converts to an analogue output (-)
White/Orange PIN#6 of 8 PIN SKIM harness in steering column
10 PIN HARNESS
Optional D2D VIP: Data to Data Vehicle Interface Protocol will replace specific analogue connections
DATA to DATA PORT (D2D): of D2D Cable plugs into the upgradeable vehicle interface module.
OPTION A: - D2D Port used to connect to USB Bootloader adaptor & computer to download & flash vehicle interface firmware.
OPTION B: - D2D Port used to connect to the data port of a remote control system equipped with ClearCode Vehicle Interface Protocol.
Remote control systems designed with ClearCode VIP can securely communicate via the D2D cable to transmit & receive data commands which initiate
specific vehicle function such as doorlocks & immobilizer override and /or request information from the vehicle such as status of entry points (doors) or ambient
température, diesel glow plug etc…ClearCode VIP represents the doorway to vehicle integration...
Blue connector
Ground When Igition is Activated
This wire must activate at the same time as main ignition.
(See Fig.2)
Door Sense Trigger connects to (-) door trigger
input wire of RCS
Lock connects to (-) Lock Output wire of RCS
Unlock connects to (-) Unlock Output wire of RCS