Filter
Top Products
12
NOTE: Only Cold and Hot Start functions can be enabled at the same time. If button #1 is pressed for
programming, Cold/Hot Start is disabled. When Buttons #2 and #3 are pressed, then the Automatic and Low
Voltage Starts are disabled.
SPECIAL PROGRAMMING MODE:
Valet Mode On
Press and hold the brake, turn Ignition Key to the Run position. Within five (5) seconds, press and
release Button #4. The horn will sound or the siren will chirp once, the parking lights once. Valet is
now on. Release the brake, turn the ignition key off.
Valet Mode Off
Press and hold the brake, turn Ignition Key to the Run position. Within five (5) seconds, press and
release Button #4. The horn will sound or the siren will chirp twice, the parking lights twice. Valet
is now off. Release the brake, turn the ignition key off.
Temporary Silent Arm/Disarm (This Arming Only)
Press and hold Button #2 for approximately two (2) seconds, the parking lights will flash once, the
unit is now programmed for Silent Arming. Press and release Button #2, the parking lights will flash
twice, and remain on for one (1) minute, the unit is now Disarmed.
Silent Arm/Disarm (Remains In Silent Mode Until Programmed Back On)
Press and hold Button #2 for approximately five (5) seconds, when arming, the parking lights will flash
without the horn or siren sounding. Hold until the parking lights flash three (3) times, release. Silent
arming/disarming is now programmed on. To program it back on, repeat these steps. After the parking
lights flash again three (3) times, silent arming/disarming is programmed off.
Runtime Programming (Engine Off)
Press and hold Button #4 (stop) for approximately 10 seconds. The horn will honk twice, then the parking
lights will begin to flash, each flash represents 5 minutes with the maximum being 25 minutes, 5 flashes.
Simply release button at whatever runtime you desire. To check programmed runtime, press and release
Button #4 (stop). The parking lights will flash for the amount of runtime you have programmed the unit
for.
Clearing the E-Prom
Press and hold the brake, now cycle the key in the ignition switch from OFF to RUN (not start)
five (5) times within four (4) seconds. If you cannot physically do this in the proper amount of
time, then remove the YELLOW ignition input wire from Ignition I and touch this YELLOW wire to
+12V constant five (5) times within four (4) seconds. Release the brake, now try the remote. The
unit should not function. If it does repeat the above procedure. If the unit does not function,
unplug the unit from both harnesses, wait one (1) minute and plug it back in. Press Button #4 (stop)
the parking lights will flash three (3) times, the unit is now back to factory default and ready
to operate.
HOW TO USE YOUR REMOTE TRANSMITTER
Starting the Vehicle with the Remote Transmitter
Press and release button #1 (start). The parking
lights will flash once, confirming the car starter
received the signal. The car will then start and
the parking lights will turn on and remain on while
the vehicle is running. To shut off the engine
before the preset time, press button #4 (stop) or
press the brake pedal or when the hood is opened.
NOTE: If your car does not start on the first crank
it will automatically attempt to start up to 2 more
times. (only in tachless mode) In tachless mode,
parking lights will wait approximately 10 seconds
before turning on.
BUTTON #1
Remote starts your vehicle
from up to a quarter mile away.
BUTTON #2
Arm locks and disarm unlocks
your power door locks.
BUTTON #3
Pops your trunk.
BUTTON #4
Turns off your remote starter and
helps you locate your car (when system
is armed).
BULLDOG
Start
Arm
Disarm
Trunk
Stop
Pit Stop: Exiting the Car with the Engine Running
Make sure the transmission is in park and press button #1 (start) before turning the ignition switch off.
(The engine will remain running for the preset time.)